User manual CHAMBERLAIN T

[. . . ] FACTORY SET C2 Wiring See page 8 for other wiring configurations OWNER'S MANUAL MODEL T INDUSTRIAL DUTY DOOR OPERATOR 2 YEAR WARRANTY Serial # (located on electrical box cover) Installation Date Wiring Type NOT FOR RESIDENTIAL USE 41B6 LISTED DOOR OPERATOR SPECIFICATIONS MOTOR TYPE: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous duty HORSEPOWER:. . . . . . . . . . . . . . . . . 1/3, 1/2, 3/4 & 1 Hp Single or Three phase SPEED:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1725 RPM VOLTAGE: . . . . . . . . . . . . . . . . . . . . . . . . . . 115, 220, 230 Single phase 230, 460, 575 Three phase CURRENT: . . . . . . . . . . . . . . . . . . . . . . . . . See motor nameplate ELECTRICAL TRANSFORMER:. . . . . . . . . . . . . 24VAC CONTROL STATION: . . . . . . NEMA 1 three button station. OPEN/CLOSE/STOP WIRING TYPE: . . . . . . . . . . . . . . . . . C2 (Factory Shipped) Momentary contact to OPEN & STOP, constant pressure to CLOSE, open override plus wiring for sensing device to reverse. See page 8 for optional control settings. LIMIT ADJUST: . . . . . . . . . . . . . . . . Linear driven, fully adjustable screw type cams. [. . . ] OPERATOR MUST BE PROPERLY GROUNDED AND PERMANENTLY WIRED IN ACCORDANCE WITH LOCAL ELECTRICAL CODES. NOTE: THE OPERATOR SHOULD BE ON A SEPARATE FUSED LINE OF ADEQUATE CAPACITY. ALL ELECTRICAL CONNECTIONS MUST BE MADE BY A QUALIFIED INDIVIDUAL. POWER WIRING 1. Be sure that the power supply is of the correct voltage, phase, frequency, and amperage to supply the operator. Refer to the operator nameplate on the cover. Using the 1-1/16" dia conduit access knockout as shown below, bring supply lines to the operator and connect wires to the terminals indicated on the WIRING CONNECTIONS DIAGRAM. DO NOT TURN POWER ON UNTIL YOU HAVE FINISHED MAKING ALL POWER AND CONTROL WIRING CONNECTIONS AND HAVE COMPLETED THE LIMIT SWITCH ADJUSTMENT PROCEDURE. TION WARNING WARNING TO AVOID DAMAGE TO DOOR AND OPERATOR, MAKE ALL DOOR LOCKS INOPERATIVE. SECURE LOCK(S) IN "OPEN" POSITION. IF THE DOOR LOCK NEEDS TO REMAIN FUNCTIONAL, INSTALL AN INTERLOCK SWITCH. WARNING IMPORTANT: THIS UNIT MUST BE PROPERLY GROUNDED. A GROUND SCREW IS SUPPLIED IN THE ELECTRICAL BOX FOR CONNECTION OF THE POWER SUPPLY GROUND WIRE. Refer only to the replacement wiring diagram for all connections. IMPORTANT NOTE: If your wiring diagram is missing, or you are unsure of the wiring type for your operator, contact the customer service department @ 1-800-528-2806. LOCATING THE CONTROL STATION All operators are supplied with some type of control station. Generally a three button station (OPEN/CLOSE/STOP) is provided. A two-position key switch or control station (OPEN/CLOSE) may be added or substituted when requested at the time of order. Mount the control station near the door. WARNING INSTALL THE CONTROL STATION WHERE THE DOOR IS VISIBLE, BUT AWAY FROM THE DOOR AND ITS HARDWARE. IF CONTROL STATION CANNOT BE INSTALLED WHERE DOOR IS VISIBLE, OR IF ANY DEVICE OTHER THAN THE CONTROL STATION IS USED TO ACTIVATE THE DOOR, A REVERSING EDGE MUST BE INSTALLED ON THE BOTTOM OF THE DOOR. FAILURE TO INSTALL A REVERSING EDGE UNDER THESE CIRCUMSTANCES MAY RESULT IN SERIOUS INJURY OR DEATH TO PERSONS TRAPPED BENEATH THE DOOR. MOUNT WARNING NOTICE IMPORTANT: Mount WARNING NOTICE beside or below the push button station. Standard Control Station OPEN Push Buttons WARNING CLOSE TO PREVENT ENTRAPMENT DO NOT START DOOR DOWNWARD UNLESS DOORWAY IS CLEAR STOP WARNING Notice 8 CONTROL WIRING (con't) Radio Controls On all models with type B2 control wiring, a terminal bracket marked R1 R2 R3 is located on the outside of the electrical enclosure. All standard radio control receivers (single channel residential type) may be mounted to this bracket. The operator will then open a fully closed door, close a fully open door, and reverse a closing door from the radio transmitter. However, for complete door control from a transmitter, a commercial three-channel radio set (with connections for OPEN/CLOSE/STOP) is recommended. WARNING DO NOT USE RADIO CONTROLS WITH YOUR OPERATOR UNLESS YOU HAVE INSTALLED SOME TYPE OF ENTRAPMENT PROTECTION DEVICE. THE USE OF RADIO CONTROLS PRESENTS POTENTIAL HAZARDS DUE TO THE USER'S ABILITY TO OPEN OR CLOSE THE DOOR WHEN OUT OF SIGHT OF THE DOOR. IN ADDITION, IF A SINGLE CHANNEL CONTROL IS USED, THE USER WILL NOT BE ABLE TO STOP THE DOOR FROM THE TRANSMITTER. W CAUTION Additional Access Control Equipment Locate any additional access control equipment as desired (but so that the door will be in clear sight of the person operating the equipment), and connect to the terminal block in the electrical enclosure as shown on the FIELD WIRING CONNECTIONS diagram. Any control with a normally (N. O. ) isolated output contact may be connected in parallel with the OPEN button. [. . . ] Complete Electrical Box Replacement Kits To order a complete electrical box kit, add a K74- prefix to the model number of your operator. For example: T5011M (Operator) = K74-T5011M (Electrical box replacement kit) Electrical Box Sub-Assemblies K72-12510 Limit Shaft Assembly K72-12511 Limit Switch Assembly Motor Kits K20-1033B2 K20-3033B4 K20-3033M5 K20-51033B K20-1050B2 K20-3050B4 K20-3050M5 K20-51050B K20-1075B2 K20-3075B4 K20-3075B5 K20-51075B K20-1100B2 K20-3100B4 K20-3100B5 Models T3311M, T3321M Models T3323M, T3338M, T3343M Model T3353M Model T3325M Models T5011M, T5021M Models T5023M, T5038M, T5043M Model T5053M Model T5025M Model T7511M, T7521M Models T7523M, T7538M, T7543M Model T7553M Model T7525M Models T1011M, T1021M Models T1023M, T1043M Model T1053M * COMPLETE ELECTRICAL BOX KITS Item Qty P/N Descrition 1 03-8024-K 1 Contactor 2 10-13790 1 Electrical Box 3 10-10115 1 Electrical Box Cover 4 21-5XXX 1 (See Varaible Components) 5 24-XXX 1 (See Varaible Components) 6 24-24-1 1 24VAC DPDT Relay 7 25-2XXX 1 (See Varaible Components) 8 25-4XXX 1 (See Varaible Components) 9 42-10040 1 Terminal Block, Radio 10 42-110 1 Terminal Block, 10 Position * Electrical Box Kits include parts from K72-12510 and K72-12511 K72-12510 Item L1 L2 L3 L4 L5 L6 L7 L8 P/N 11-10021 12-10028 13-10024 15-48B9A 80-10025 80-10026 86-CP05-108 87-E-038 LIMIT SHAFT ASSEMBLY KIT Description Limit Shaft, Standard T Flange Bearing, 3/8" I. D. Limit Nut Sprocket 48B9 x 3/8" Bore Washer, Shim 3/8" I. D. x 1 Long E Ring, 3/8" Qty 1 2 2 1 1 4 1 1 Shaft Assemblies K72-12506 Clutch Shaft Assembly (1/3 & 1/2 HP Models) K72-12507 Clutch Shaft Assembly (3/4 & 1HP Models) K72-12508 Output Shaft Assembly (1/3 & 1/2 HP Models) K72-12509 Output Shaft Assembly (3/4 & 1 HP Models) Hardware, Track, Drive Chain Kits K72-12491 Hardware Kit See pg. [. . . ]