User manual CHICAGO 41856

[. . . ] Attach a Down Support (#9) to the bottom hole on a Leg (#8) using a Bolt (#12), a Washer (#14), and a Nut (#13). Make sure you attach to the inside of the angle iron on the Leg (#8). Move up the same Leg (#8) to the middle hole and attach a Mid Support (#16) using a Bolt (#12), a Washer (#14), and a Nut (#13). Next, repeat the process adding a second Down Support (#9) and a Mid Support (#16) to the leg you just assembled. [. . . ] Next, repeat the process adding a second Down Support (#9) and a Mid Support (#16) to the leg you just assembled. You should now have one Leg (#8) with two Down Supports (#9) and two Mid Supports (#16). Take both remaining Legs (#8) and attach them to Down Supports (#9), and Mid Supports (#16) on the previously assembled Leg (#8). Next, put the last Down Support (#9) and Mid Support (#16) between the two remaining Legs (#8). Tighten all of the Nuts (#13) and Bolts (#12). The Upper Supports (#15) are "L" shaped with one end shorter than the other. Attach the shorter end to the upper holes on the Legs (#8) of the tripod you just constructed using a Bolt (#12), a Washer (#14), and a Nut (#13), for each Upper Support (#15). See the Assembly Diagram on Page 4 to show correct position of each Upper Support (#15). The Base Stand (#7) has two metal triangles welded to the top section of it, below the Lock Pin (#11) hole. Lower the Base Stand (#7) into the tripod you just constructed, bottom first. Remove the Lock Pin (#11) and raise the Shaft (#6) so that the Pan (#1) rests under the selected auto part needing support. Turn the Handles (#10) raising the Pan (#1) until it securely supports the auto part. If necessary tighten Handles (#10). SKU 41856 REV 07k Page 3 Assembly Drawing and Parts List No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Description Pan Screw Rod Screw Nut Bearing Position Rod Shaft Base Stand Legs Down Support Handle Lock Pin Bolt M10x20 Nut M10 Washer #10 Upper Support Mid Support Qty 1 1 1 1 1 1 1 3 3 2 1 22 21 21 3 3 SKU 41856 Page 4 liMiTeD 90 DaY WaRRanTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS ExPRESSLY IN LIEU OF ALL OTHER WARRANTIES, ExPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. [. . . ] THIS WARRANTY IS ExPRESSLY IN LIEU OF ALL OTHER WARRANTIES, ExPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. [. . . ]