User manual CHICAGO 45656

[. . . ] TIRE CHANGER SEMI-AUTOMATIC Model 45656 OpERATING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight Tools®. 3491 Mission Oaks Blvd. , Camarillo, CA 93011 Visit our website at: http://www. harborfreight. com Read this material before using this product. Failure to do so can result in serious injury. [. . . ] Release pressure on the Bead Breaker Pedal when the Blade has reached the end of its travel and/or when the tire bead is broken. (See Figures B, E, and H. ) Rotate the tire slightly, and repeat the procedure around the entire circumference of the wheel rim until the bead is completely detached from the rim. Repeat the above Steps for the other side of the wheel/tire. 5. 6. To Remove The Tire From The Wheel: 1. WARNING: Before carrying out this procedure, deflate the tire fully, and remove all the wheel weights. Spread tire grease (or a similar lubricant) liberally on the complete circumference of the broken tire bead. NOTE: Failure to lubricate the tire bead may cause serious damage to the bead. Place the wheel/tire evenly on the Turntable (1C). (See Figure E. ) To lock the wheel on the Turntable (1C), proceed as follows according to the wheel rim size: Rims from 10" to 18": Position the four Jaws (17C) according to the reference mark located on the Turntable (1C) by depressing the Jaw Clamp Pedal (26E) halfway down. 4. SKU 45656 For technical questions, please call 1-800-444-3353. Page 9 Place the wheel on the four Jaws (17C) and, while keeping the wheel rim pressed down, depress the Jaw Clamp Pedal (26E) as far down as it will go. Check to make sure the wheel is firmly secured by the Jaws (17C). Rims from 12" to 20": Position the four Jaws (17C) so that they are completely closed. Place the wheel on the four Jaws (17C) and depress the Jaw Clamp Pedal (26E) to open the Jaws, thereby locking the wheel rim in place. Check to make sure the wheel is firmly secured by the Jaws (17C). MOUNTING HEAD (#15A) TOOLS SHAFT (#13A) LEVER (#1F) FIGURE I 5. Lower the Tools Shaft (13A) until the Mounting Head (15A) rests next to the wheel rim and on top of the tire. Then, lock the Tools Shaft in position, using the Block Support (7A). (See Figures E and I. ) Insert the Lever (1F) between the tire bead and the front section of the Mounting Head (15A). (See Figures E and I. ) Move the tire bead over the Mounting Head (15A) by pulling upward on the Reverse Pedal (59E). NOTE: To avoid damaging the inner tube (if there is one), it is recommended to perform this Step with the inner tube valve stem positioned about 1" to the right of the Mounting Head. (See Figures B and I. ) With the Lever (1F) held in position, rotate the Turntable (1C) in a clockwise direction by fully depressing the Reverse Pedal (59E). Continue until the tire is completely separated from the wheel rim. Remove the inner tube (if there is one), and repeat the above Steps for the other side of the wheel/tire. 6. [. . . ] And remove the inner tube (if there is one). 11. Insert the lever between the other side of the tire bead and the front section of the mounting head. Move the tire bead over the mounting head. 12. Repeat the above steps for the other side of the tire. SKU 45656 For technical questions, please call 1-800-444-3353. Page 25 GRApHIC OpERATING (MOUNTING) 1. [. . . ]