User manual CHICAGO 47423

[. . . ] Do not wear loose clothing or jewelry, as they can become caught in moving parts. wear a protective hair covering to prevent long hair from becoming caught in moving parts. If wearing a long-sleeve shirt, roll sleeves up above elbows. Keep proper footing and balance at all times to prevent tripping, falling, back injury, etcetera. [. . . ] Do not modify this equipment, and do not use this equipment for a purpose for which it was not intended. WARNINg: The warnings, precautions, and instructions discussed in this manual cannot cover all possible conditions and situations that may occur. The operator must understand that common sense and caution are factors, which cannot be built into this product, but must be supplied by the operator. THE MODEL 42709 TRAILER. Make sure to attach the Steel Side Panel Kit to the Trailer manufacturer's recommended assembly points. ALWAYS EXAMINE THE STEEL SIDE PANEL KIT FOR LOOSE MOUNTINg BOLTS, STRUcTURAL cRAcKS, BENDS, DAMAgE, AND ANY OTHER cONDITION THAT MAY AFFEcT ITS SAFE OPERATION. Do not use the Steel Side Panel Kit even if minor damage appears. when installing the Steel Side Panel kit, the trailer must be located on a level, solid surface, with tires blocked so that the trailer cannot roll. 5. UNPAcKINg when unpacking, check to make sure all the parts shown on the Parts List (page 9) are included. If any parts are missing or broken, please call harbor freight Tools at the number shown on the cover of this manual as soon as possible. SPEcIFIc PRODUcT WARNINgS AND PREcAUTIONS 1. THIS STEEL SIDE PANEL KIT IS DESIgNED FOR USE ONLY WITH THE MODEL 42709 TRAILER (AVAILABLE FROM HARBOR FREIgHT TOOLS). PROFESSIONAL TEcHNIcAL ASSEMBLY KNOWLEDgE IS REQUIRED TO SEcURELY AND PERMANENTLY ATTAcH THE STEEL SIDE PANEL KIT TO THE MODEL 42709 TRAILER. ONLY A QUALIFIED TEcHNIcIAN SHOULD PERFORM THE ASSEMBLY. MAKE SURE TO READ AND UNDERSTAND ALL INSTRUcTIONS AND SAFETY PREcAUTIONS AS OUTLINED IN THE MANUFAcTURER'S MANUAL FOR SKU 47423 2. 3. For technical questions, please call 1-800-444-3353. Page 3 PRODUcT OVERVIEW The Steel Side Panel Kit is designed for use only with the Model 42709 Trailer (available from harbor freight Tools). Its assembly onto the Trailer requires a 3/4" thick, 4' x 8' plywood board (not provided). Attaching the Steel Side Panel Kit to the Trailer will also require drilling mounting holes through the plywood board. ONLY A QUALIFIED TEcHNIcIAN SHOULD PERFORM THE ASSEMBLY. DRILL 3/8" hOLES notch notch FIgURE A 2. Use the measurements taken in Step #1 to mark and drill ten holes through the 3/4" thick, 4' x 8' plywood board. (See Figure A. ) ASSEMBLY INSTRUcTIONS NOTE: for additional references to the parts listed below, refer to the Assembly Diagram (page 9). NOTE: You will need to notch out the plywood to allow for the hinge as shown in Figure A. ALIGN PRE-DRILLED hOLES IN PLYwOOD wITh fRAME MOUNTING hOLES 3/4", 4'x 8' PLYwOOD BOARD 1. Measure the on-center distance between the ten mounting holes located on the front frame and two side frames of the Trailer, locations indicated above. MODEL 42709 TRAILER FIgURE B 3. With assistance, place the 3/4" thick, 4' x 8' plywood board on the frame of the Trailer. Make sure to align the ten predrilled holes in the plywood board with the ten mounting holes on the front and two sides of the Trailer frame. (See Figure B. ) Place the front Panel (1) on the front of the front end of the Trailer and underneath the plywood board. Make sure to align the two mounting holes at the bottom of the front Panel with the SKU 47423 4. Page 4 For technical questions, please call 1-800-444-3353. previously aligned holes in the plywood board and Trailer frame. Insert two Bolts (6) downward through the holes in the front Panel, plywood board, and Trailer frame. [. . . ] Check for loose mounting bolts, misalignment or binding of moving parts, cracked, bent, or broken parts and any other condition that may affect its safe operation. Importantly, check the Steel Side Panel Kit regularly to assure the welds remain solid. If abnormal noise or vibration occurs, have the problem corrected before further use. TO cLEAN, use only water and a mild detergent. 2. REV 03f SKU 47423 For technical questions, please call 1-800-444-3353. Page 7 PLEASE READ THE FOLLOWINg cAREFULLY ThE MANUfACTURER AND/OR DISTRIBUTOR hAS PROVIDED ThE PARTS LIST AND ASSEMBLY DIAGRAM IN ThIS MANUAL AS A REfERENCE TOOL ONLY. [. . . ]