User manual CHICAGO 66192

[. . . ] Insert Axles (5) and into the axle brackets located on the outside curved part of the Stand Frame (1). Slide a Flat Washer (8) over each end of the Axle (5) and up against the axle bracket. Slide a Bushing (7) over the ends of the Axle (5) and up against the Flat Washers. Slide two Casters (6) over each end of the Axle and over the Bushings (7). [. . . ] Do not assemble when tired or when under the influence of drugs, alcohol or medication. 2. Do not allow children to play with or near this item. Inspect before use; do not use if parts are loose or damaged. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement. 1. operation Adjust the position of the Paddle Adapters (2) to match motorcycle's dual swing arm width. Roll the Stand behind the motorcycle so that the motorcycle is in the middle of the Stand Frame. Move Stand to where the Paddles are under the swing arm. Adjust Paddle Adapters (2) inward into position. Make sure the Paddles are snug up against the swing arm and tighten Knobs (3). asseMblY InstructIons read the entIre IMportant saFetY InForMatIon section at the beginning of this document including all text under subheadings therein before set up or use of this product. SKU 66192 For technical questions, please call 1-800-444-3353. Page 2 2. If the motorcycle kick stand is the type that holds the motorcycle upright, use it. If not, have an assistant hold the motorcycle upright. please read tHe FolloWInG careFullY THe MANUFACTUReR AND/OR DISTRIBUTOR HAS PROvIDeD THe PARTS LIST AND ASSeMBLy DIAgRAM IN THIS DOCUMeNT AS A ReFeReNCe TOOL ONLy. NeITHeR THe MANUFACTUReR OR DISTRIBUTOR MAKeS ANy RePReSeNTATION OR WARRANTy OF ANy KIND TO THe BUyeR THAT He OR SHe IS qUALIFIeD TO MAKe ANy RePAIRS TO THe PRODUCT, OR THAT He OR SHe IS qUALIFIeD TO RePLACe ANy PARTS OF THe PRODUCT. IN FACT, THe MANUFACTUReR AND/OR DISTRIBUTOR exPReSSLy STATeS THAT ALL RePAIRS AND PARTS RePLACeMeNTS SHOULD Be UNDeRTAKeN By CeRTIFIeD AND LICeNSeD TeCHNICIANS, AND NOT By THe BUyeR. THe BUyeR ASSUMeS ALL RISK AND LIABILITy ARISINg OUT OF HIS OR HeR RePAIRS TO THe ORIgINAL PRODUCT OR RePLACeMeNT PARTS THeReTO, OR ARISINg OUT OF HIS OR HeR INSTALLATION OF RePLACeMeNT PARTS THeReTO. 3. 4. Lower the handle engaging the Paddle Adapters (2) with the swing arm. With the Paddle Adapters securely supporting the swing arm, lower the Stand Frame (1) to the ground. parts lIst & asseMblY dIaGraM part 1 2 3 4 5 6 7 8 9 description Stand Frame Paddle Adapter Knob Lock Nut Axle Caster Bushing Flat Washer Front Fork Adapter (Optional)* Qty. The handle resting on the ground acts as a support base for the Stand. 1. ) cautIon: Do not attempt to lift the motorcycle if the Paddle Adapters are not fully engaged with the swing arm. To lower the motorcycle, have an assistant support the motorcycle by its handlebars. Raise the Stand Frame (1) handle from the ground carefully, lowering the motorcycle. [. . . ] Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTy IS exPReSSLy IN LIeU OF ALL OTHeR WARRANTIeS, exPReSS OR IMPLIeD, INCLUDINg THe WARRANTIeS OF MeRCHANTABILITy AND FITNeSS. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. [. . . ]