User manual CHICAGO 66958

[. . . ] Sku 66958 For technical questions please call 1-800-444-3353 Page 2 GeneRal SaFeTY WaRninGS anD PReCauTiOnS 1. Cluttered, damp or wet work areas invite injuries. Do not allow children to handle this product. When not in use, tools and equipment should be stored in a dry location to inhibit corrosion. [. . . ] Only use accessories intended for use with this product. Approved accessories are available from Harbor Freight Tools. Sku 66958 For technical questions please call 1-800-444-3353 Page 3 12. Keep this tool clean and dry for better and safer performance. uSe THe RiGHT PRODuCT FOR THe RiGHT JOB. There are certain applications for which this product was designed. Do not use small equipment, tools or attachments to do the work of larger industrial equipment, tools or attachments. Do not use this product for a purpose for which it was not intended. PRiOR TO uSinG THiS PRODuCT, maKe SuRe TO ReaD anD unDeRSTanD all inSTRuCTiOnS anD SaFeTY PReCauTiOnS aS OuTlineD in THe VeHiCleS manuFaCTuReR'S manualS. neVeR WORK unDeRneaTH a VeHiCle WiTHOuT uSinG aDDiTiOnal SaFeTY SuPPORT DeViCeS (i. e. , JaCK STanDS) TO SuPPORT THe WeiGHT OF THe VeHiCle. Read and understand all safety warnings and instructions provided in the instruction manual of the vehicle as well as the jack stand being used to support the vehicle. OPeRaTinG inSTRuCTiOnS To attach The Plug Bolt To The C-Frame: This product contains or produces a chemical known to the State of California to cause cancer and birth defects (or other reproductive harm). (California Health & Safety Code 25249. 5 et seq. ) WaRninG (NOT PROVIDED) STeel Ball (NOT PROVIDED) O-RinG (NOT PROVIDED) FORCinG SCReW PluG BOlT (14) (Included) C-FRame (NOT PROVIDED) Figure a Sku 66958 For technical questions please call 1-800-444-3353 Page 4 This set is recommended for use with the 3-in-1 Service Kit (Model 38335), which is available from Harbor Freight Tools. Read and understand all safety warnings and instructions provided in the instruction manual of the 3-In-1 Service Kit before using the kit. All parts mentioned below are listed and shown on page 10 of this manual. The illustration in Figure A depicts a disassembled C-Frame, a tool that is part of the 3-In-1 Service Kit (Model 38335) and recommended for use with this Master Ball Joint Adapter Set. To operate the Master Ball Joint Adapter Set, it will be necessary to attach the Plug Bolt (part 14) contained in this Set to the C-Frame of the 3-In-1 Service Kit. (See Figure a, and Parts list on Page 10. ) 3. To do so, unscrew and remove the Forcing Screw, Steel Ball, and O-Ring from the C-Frame. (See Figure a, and Parts list on Page 10. ) 4. Make sure the Steel Ball and O-Ring remain inside the Forcing Screw. Then, insert the Plug Bolt (part 14) into the Forcing Screw, if required. Screw the threaded end of the Forcing Screw, with its Steel Ball, O-Ring, and attached Plug Bolt (part 14) back into the threaded end of the C-Frame toward the unthreaded hole of the C-Frame. [. . . ] We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. [. . . ]