User manual CHICAGO 8884

[. . . ] 3-IN-1 Jump-start 8884 set up aNd OperatINg INstructIONs Note: after purchase and before initial use of the Jump-start, fully charge the Jumpstart battery until the dc charging led turns off. after each jump start, fully recharge the battery until the dc charging led turns off. Fully charge Jumpstart battery every 30 days to ensure long battery life. Visit our website at: http://www. harborfreight. com read this material before using this product. [. . . ] Lead-acid batteries vent hydrogen gas during normal operation and charging. Hydrogen is highly flammable and explosive. Charge batteries only in a well-ventilated area. Do not allow the red and black clamps to come in contact with each other or the same metal object. When charging, first connect the red (+) clamp to the positive (+) battery terminal. Connect the negative (-) clamp to a non-moving metal engine part for negative ground systems. Only use the charger on 12 V systems on vehicles or boats. Do not use as a replacement for a vehicle battery. The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure. REV 09k SKU 8884 For technical questions, please call 1-800-444-3353. Page 3 cONtrOls aNd cOmpONeNts FIgure 1 (FRONT) Red Clamp Work Light Test Meter Light DC Charging Switch LED Recharging Receptacle On/Off Black Clamp clamps only. Keep it in the "Off" position except when jumpstarting. 120 V~ charging FIgure 3 12 VDC Cigarette Lighter Receptacle Voltage Test Switch 120 V~ Charging Plug (male) Compressor On/Off Switch Cigarette Lighter Plug in 120 V~ Plug in FIgure 2 (BACK) 1. Screw (Battery Removal) Plug an extension cord into a wall outlet and plug the female end of the extension cord into the 120V male Charging Plug of the 120V~ Charging Port (see FIgure 3, above). Before first use, fully charge the Jump-start battery until the dc charging led turns off. after each jump start, fully recharge the battery until the dc charging led turns off. It may take up to 48 hours to fully charge the Jump-start battery. Fully recharge Jump start battery every 30 days to ensure long battery life and reliability. Pressure Gauge 2. 3. Air Hose Storage with Universal Adapter for Tires Air Hose chargINg Note: After purchase and before initial use, fully charge the Jump-Start battery until the DC charging LED turns off. The ON/Off switch (See FIgure 1) regulates power to the reV 09g, 09k, 09l 4. Note: The charger unit comes equipped with an automatic shut off LED to prevent overcharging. Leave the unit plugged in to make sure it is charged for emergencies. Page 4 SKU 8884 For technical questions, please call 1-800-444-3353. 12 Vdc charging Note: This system is equipped with a 12 VDC Cigarette Lighter Adapter so you can charge the Jump-Start from a vehicle or boat battery. This method of recharging will not charge the unit as fully as when using the 120 V~ charging method. Only use this method in an emergency situation, as this recharging method may shorten the life of the Jump-Start. [. . . ] If filling something other than a tire, read the instruction manual to determine the correct air pressure. WarNINg!do not let the black and red clamps to touch each other or a common metal conductor. When the engine is running, switch off the unit. Disconnect the black (-) Booster Cable Clamp and return it to its position on the Jump-Start. [. . . ]