User manual CHICAGO 92655

[. . . ] requires a Class 3 hitch on the vehicle. maximum tongue weight, add Carrier weight of about 30 lb. ) (Class 3 Hitch = 500 lb. maximum tongue weight) Safety Warnings and Precautions WARNING: When using product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Read all instructions before using this product! [. . . ] Harbor Freight Tools is not responsible for damage to persons or cargo. Do not lean or climb on the side panels. Suddenly dropping or bouncing a load on the Cargo Carrier may create, for a brief instant, an excess load, which may result in damage to the product and/or personal injury. Additionally, if the vehicle hits a bump, a slight play in the receiving hitch or a movement in the load could result in a momentary dynamic loading effect that could dramatically increase the actual weight load. Check the hitch-to-Carrier connection for any looseness. This momentary dynamic loading effect could result in damage to the Cargo Carrier, the load and possible personal injury. Be aware of the possible risk of fire and damage to property resulting from the vehicle's exhaust system pointing at or running near the cargo put in this Cargo Carrier. Before installing the Cargo Carrier, check to make sure that the exhaust pipe is not pointing in the direction of the cargo. Flammable cargo can ignite from exposure to heat. Other cargo can be damaged from the heat. Always be aware of this potential danger, and never use the Cargo Carrier if the risk exists. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking your Aluminum Cargo Carrier, check to make sure all parts listed on page 5 are included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353. SKU 92655 For technical questions, please call 1-800-444-3353. Page 3 Assembly Your Cargo Carrier will require some light assembly prior to use. It is important that you read the entire manual to become familiar with the product BEFORE you assemble and use the Cargo Carrier. Before assembling and operating the Cargo Carrier be sure that you have all parts described in the Parts List and Assembly Diagram located on the last pages of this manual. Align the Top Brace (1) with the Body (2). Connect them with the two Reflectors (14) on the outside rear corners of the Cargo Carrier using Bolt (6) and Nut (7) - see Assembly diagram. The reflective side must be facing the rear of the Cargo Carrier. Figure 1 Reflector (14) Reflector (14) Top Brace (1) Small Vertical Support (5) Body (2) Large Support (4) 2. Use the Small Vertical Supports (5) to connect the Top Brace (1) to the Body (2): Attach each end of the Small Vertical Support (5) to the Top Brace (1) and the Body (2) using Bolt (6) and Nut (7) - see Assembly diagram and Figure 1. Repeat for each Small Vertical Support (5). Attach the Large Supports (4) so that the top and bottom of the Large Support (4) is attached to the Top Brace (1) with three Bolts (6) and three Nuts (7) on each end. [. . . ] We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THiS WArrANTy iS exPreSSLy iN Lieu OF ALL OTHer WArrANTieS, exPreSS Or iMPLieD, iNCLuDiNg THe WArrANTieS OF MerCHANTABiLiTy AND FiTNeSS. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. [. . . ]