User manual CHICAGO 95408

[. . . ] Wear ANSI-approved safety impact goggles when asembling this product. For technical questions, please call 1-800-444-3353 PAGE 2 3. SKU 95408 4. Do not force the Pintle Hook. Use the correct product for your application. The correct product will do the job better and safer at the rate for which it is designed. [. . . ] Prior to using this product, make sure to read and understand all instructions and safety precautions as outlined in the service manuals for the towing vehicle and trailer (or object) being towed. Make sure the towing vehicle is capable of towing the trailer and its payload. Make sure the hitch receiver on the towing vehicle is capable of towing the trailer and its payload. The towing capacity of the hitch receiver is typically stamped on the receiver. The Bolts, Lock Washers, and Nuts (not included) used to mount the Pintle Hook to the Pintle Mount (not included) MUST be rated a minimum Grade #8 hardness. Do not attempt to use lesser grade mounting hardware. For technical questions, please call 1-800-444-3353 PAGE 3 5. 6. 7. 13. 14. SKU 95408 15. WARNING!The warnings and cautions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. UNPACKING When unpacking, check to make sure all the parts shown in the Parts List on page 6 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the front cover of this manual as soon as possible. ASSEMBLY INSTRUCTIONS To Attach The Pintle Hook To A Pintle Mount: 1. NOTE: The Pintle Hook is designed only for use with the Harbor Freight Tools Model 95407 Pintle Mount (sold separately). (See Figure A. ) The Pintle Mount is designed to allow for adjusting the height of the mounted Pintle Hook. To adjust the height, align the four mounting holes in the Pintle Hook with either the four top mounting holes in the Pintle Mount or the four bottom holes in the Pintle Mount. (See Figure A. ) Once the height of the Pintle Hook is determined, secure the Pintle Hook to the Pintle Mount, using the four Grade #8 Bolts, four Lock Washers, and four Nuts provided with the Pintle Mount. CAUTION: Make sure the four Nuts are firmly tightened onto the four Bolts. (See Figure A. ) WARNING! THE FOUR BOLTS, LOCK WASHERS, AND NUTS USED TO ATTACH THE PINTLE HOOK TO THE PINTLE MOUNT MUST BE RATED A MINIMUM GRADE #8. 2. 3. MODEL 95407 PINTLE MOUNT (NOT INCLUDED) MOUNTING HOLES FOR HIGHER MOUNTING OF PINTLE HOOK FOR LOWER MOUNTING OF PINTLE HOOK BOLTS, LOCK WASHERS, NUTS VEHICLE HITCH RECEIVER END VIEW MODEL 95407 PINTLE MOUNT FIGURE A SKU 95408 (NOT INCLUDED) SIDE VIEW For technical questions, please call 1-800-444-3353 PAGE 4 To Attach The Pintle Mount And Pintle Hook To A Vehicle's Hitch Receiver: 1. Insert the Pintle Mount into a 2" x 2" vehicle hitch receiver (not included). (See Figure A. ) Align the hitch pin hole in the Pintle Mount with the hitch pin hole in the vehicle hitch receiver. (See Figure A. ) Secure the Pintle Mount and Pintle Hook to the vehicle hitch receiver by inserting a hitch pin (not included) through the hitch pin holes of the Pintle Mount and vehicle hitch receiver. Then, insert a safety pin (not included) through the opening in the hitch pin. (See Figure A. ) 2. 3. OPERATNG INSTRUCTIONS 1. [. . . ] We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. [. . . ]