User manual CHICAGO 95974

[. . . ] A moment of inattention during installation may result in serious personal injury and/or property damage. keep bystanders and children away while installing Light kit. Always wear ANSI approved eye protection. Dust mask, nonskid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. [. . . ] warning: the warnings and precautions discussed in this manual cover all possible condition and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. assEMbLy instructiOns note: For additional information regarding the parts listed in the following pages, refer to the Parts List and Assembly Diagram. NOTE: CONNECT THE LIGHT KIT AFTER THE TRAILER IS FULLY ASSEMBLED. 1. Connect the BROWN wire of the Color Coded Trunk Harness (5) to the towing vehicle's Tail Light wire. Connect the YELLOW wire of the Color Coded Trunk Harness to the vehicle's Left Hand Stop & Turn light. Connect the GREEN wire of the Color Coded Trunk Harness to the vehicle's Right Hand Stop & Turn light. Make sure to use the BLUE Wire Splitter Connectors to make these connections. Diagram. ) Attach the WHITE GROUND wire to the towing vehicle's frame. Diagram. ) for technical questions, please call 1-800-444-3353. 2. SKU 95974 Page 3 3. NOTE: If the towing vehicle has rear turn signals separated from its stop lights, you will need to install additional hardware. Contact a qualified service technician for guidance. suggEstED usE L. H. Stop & Turn (Green) Right Rear Splitter Wire Connector Side Marker (Amber) Green Brown Splitter Wire Connector Ground (White) Tail License, Side Marker (Brown) Splitter Wire Connector Side Marker (Amber) Yellow Brown 3 Rear Markers (Red) Required for Trailers over 80' Wide (Not Included) Left Rear & License Bracket Trailer Light Mounting And Connection: 1. Mount the Stop-Tail-Turn Light (1), marked "L. H. " (with the License Window), on the left rear of the trailer with its side marker to the outside of the trailer. Then, mount the License Plate Bracket (3) with the Stop-Tail-Turn Light. Diagram. ) Mount the Stop-Tail-Turn Light (1), marked "R. H. " (without the License Window), on the right rear of the trailer with its side marker to the outside of the trailer. Diagram. ) Use the Metal Frame Clips included in the Mounting Hardware Package (6) to mount each half of the Split Y-Style Harness (4) down each side of the trailer. Run the YELLOW and BROWN wires down the left side and GREEN and BROWN wires down the right side of the trailer. Diagram. ) Connect the YELLOW and BROWN wires to the left hand Stop-Tail-turn Light (1) with the Wire Nut Connectors included in the Mounting Hardware Package (6). Diagram. ) Connect the GREEN and BROWN wires to the right hand Stop-Tail-turn Light (1) with the Wire Nut Connectors included in the Mounting Hardware Package (6). Diagram. ) for technical questions, please call 1-800-444-3353. 2. 3. 4. 5. SKU 95974 Page 4 6. 7. Attach the WHITE GROUND wire to the trailer tongue or frame. Diagram. ) Mount the two Marker Clearance Lights (2) in the areas shown in the illustration. Connect each wire from the Marker Clearance Lights to the BROWN wire on each half of the Split Y-Style Harness (4). [. . . ] Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS ExPRESSLY IN LIEU OF ALL OTHER WARRANTIES, ExPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. [. . . ]