User manual CHICAGO 96933

[. . . ] warning indicates a hazardous situation which, if not avoided, could result in death or serious injury. caution, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. notice is used to address practices not related to personal injury. caution, without the safety alert symbol, is used to address practices not related to personal injury. SaFetY ruleS warning! [. . . ] If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. SpeciFicationS Electrical Requirements Bulb Type Connector 12 VDC 4. 3 A 12 VDC 21/5 W (#1157 Type) 4-way Flat wiring note: Some towing vehicles may already have a 4-way Flat Connector, "Trunk" plug wired in. For those vehicles, skip the following wiring instructions. if you do not have experience doing this type of automotive electrical wiring or if the wiring in your vehicle differs from that explained below, have an automotive service technician connect the wiring. Identify the towing vehicle's wires in the trunk that correspond to the circuits indicated in the Wiring Color Code diagram to the right. The white ground wire from the Pigtail (22) may be connected to a bolt or appropriate component on the vehicle to establish a ground instead of a ground wire. wiring color code note: This is the wiring configuration of the "Trunk" 4-way Flat Connector (23). The towing vehicle may have a different wiring color code. "trunk" 4-way Flat connector (23) white Ground Brown Running Lights Yellow Left Stop and Turn Lights green Right Stop and Turn Lights wiring pigtail (22) 2. Connect the wires from the Wiring Pigtail (22) to the proper vehicle circuit wires using Wire Splices (21). When the supplied splices are used, generally no wire stripping or cutting would be wire Splice (21) usage required. Follow these three steps and refer to the illustration to the a) insert pigtail (22) wire right: a. Insert the end of the Pigtail (22) wire into the `dead-end' channel of the Splice. Insert the wire all the way to the end of the channel as shown. Place the Splice around the correct vehicle circuit wire. Make sure both wires stay properly in place while the cover is closed until it snaps together. B) place splice around vehicle wire into `dead-end' channel c) close Splice cover securely SKU 96933 For technical questions, please call 1-800-444-3353. Page 4 3. 5. Verify that all wires are held securely. Plug the "Trunk" Connector (23) into the "Trailer" Connector (18). if the wire Splices (21) are used improperly and damage the vehicle's wiring, the vehicles rear lights may fail, resulting in a traffic hazard. have an assistant operate the vehicle's lights while you carefully check that the vehicle lights and the towing lights all work properly after installation. If any function of the vehicle or towing lights does not work, do not drive the vehicle. Carefully inspect the splice connection and the circuit that failed and repair the problem and retest before use. Disconnect the "Trailer" Connector (18) if the light kit is not going to be used yet. 6. Set up 1. To help avoid scratches, clean the mounting locations and clean the protective labels under the lights. Set the lights on the back of the vehicle being towed so that the RED side of each light faces backwards. [. . . ] note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 96933 For technical questions, please call 1-800-444-3353. Page 6 aSSeMBlY diagraM Part Numbers 21, 22, 23 - see photo's on page 4. SKU 96933 For technical questions, please call 1-800-444-3353. Page 7 liMited 90 daY warrantY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. [. . . ]