User manual CHICAGO 99721

[. . . ] caution, without the safety alert symbol, is used to address practices not related to personal injury. general Safety Warnings WaRning Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in serious injury. Save all warnings and instructions for future reference. Cluttered or dark areas invite accidents. [. . . ] Maintain labels and nameplates on the tool. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement. Keep bystanders out of the area during assembly, loading and unloading. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. 4. 5. 6. 7. 8. 9. motorcycle carrier Safety Warnings 1. Secure motorcycle frame and wheels securely using ratcheting tie downs (not included) and included pins. Save tHeSe inStRuctionS. SKU 99721 For technical questions, please call 1-800-444-3353. Page 3 SpeciFicationS Weight Capacity Receiver Size 400 Pounds 2" Motorcycle Platform Size 78-3/4" L X 8-5/8" W 7 5 18, 19 15 13, 14 20 unpacKing When unpacking, make sure that item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at number shown on cover of this manual as soon as possible. 17 4 11 12 3 2. Remove all Bolts (11, 12, 20), Washers (14, 18), Nuts (13, 15, 19), Pins (5, 7) and Brackets (4, 17) from Tube (3), as shown above. Insert Tube into Platform (1) and secure with two Bolts (12), Washers (14), and Nuts (13). Attach Tie Down Brackets (4) to Tube with Bolt (11) and Nut (15). Insert Tube into Class III (or better) 2" receiver of a vehicle and lock in place with Hitch Pin (5). Insert R-Pin (7) through hole in Hitch Pin to hold it in place. Attach Stabilizers (17) to Tube using Bolt (20), Washer (18), and Nut (19). Tighten Stabilizers in place to reduce vibration of the Carrier. aSSembly Read entiRe impoRtant SaFety inFoRmation section at beginning of this manual including all text under subheadings therein before set up or use of this product. 21 22 1 3. 4. 5. 6. 23 1. Attach the two Wheel Clamps (23) to the Platform (1), using two Bolts (21) and Lock Nuts (22) each Clamp. SKU 99721 For technical questions, please call 1-800-444-3353. Page 4 opeRation Read entiRe impoRtant SaFety inFoRmation section at beginning of this manual including all text under subheadings therein before set up or use of this product. 7. Push motorcycle completely onto carrier. Install both Wheel Lock Pins through motorcycle wheels and secure with R-pins (6). note: If a wheel cannot be secured with Wheel Lock Pins, use a properly-rated ratchet tie downs to firmly secure it to its end of platform. Remove LEFT Wheel Lock Pin (8), Adjustment Pin (16), and their R-pins (6). Move Adjustment Pin (16) so that motorcycle's weight will be centered on Platform. Some larger wheels will require Adjustment Pin to be left off entirely. If used, secure Adjustment Pin in place with a R-pin (6). Remove Wingnut (10), Press Plate (9) and Ramp (2). [. . . ] To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. [. . . ]