User manual CHICAGO MOTOCROSS DIRT BIKE STAND

[. . . ] caution, without the safety alert symbol, is used to address practices not related to personal injury. general safety Warnings Warning read all safety warnings and instructions. Failure to follow the warnings and instructions may result in serious injury. save all warnings and instructions for future reference. Cluttered or dark areas invite accidents. [. . . ] If unreadable or missing, contact Harbor Freight Tools for a replacement. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. saVe tHese instructions. Motocross bike stand safety Warnings 1. Keep clear of Release Bar and do not leave unattended while supporting load. Raise and lower using second person to stabilize load. Keep out from under load while lowering. Inspect before every use; do not use if parts are loose or damaged. Operate on flat and level surface. 3. SKU 66552 For technical questions, please call 1-800-444-3353. Page 3 speciFications Weight Capacity 350 lb. Pedal U-Shaped Bracket unpacking When unpacking, make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. · Washer (9); Long Bolt Insert Long Bolt (6) through: · One hole in U-shaped Bracket under Saddle (1); · Bushing (10); · Hole in end of Pedal (3); · Bushing (10); · Other hole in U-shaped Bracket; · Washer (9). Insert Short Bolt (7) through: · Washer (9); · Mounting Bracket (5); · Washer (9); · Remaining hole in Pedal (3); · Washer (9); · Remaining Mounting Bracket (5); · Washer (9). asseMblY read the entire iMportant saFetY inForMation section at the beginning of this manual including all text under subheadings therein before set up or use of this product. note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Make sure rubber end caps are secured into feet of Base (2). Steps 4 and 5 5. 6. Secure Short Bolt with a Lock Nut (8). Insert remaining Short Bolt (7) through: · Washer (9); · Release Bar (4); · Washer (9); · Remaining hole in Mounting Bracket (5); · Washer (9); Steps 6 and 7 Steps 2 and 3 SKU 66552 For technical questions, please call 1-800-444-3353. Page 4 · Hole in foot on Base (2); · Washer (9); · Remaining hole in second Mounting Bracket (5); · Washer (9). Before using the Bike Stand with a load, test the operation of the Pedal and Release Bar, without any load, following the operating instructions below. r-pin (12) locking pin (11) 4. operating instructions read the entire iMportant saFetY inForMation section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Locate Stand on hard, flat, and level surface able to withstand load without deforming. Center dirt bike over Saddle and secure to saddle with tie-down strap (sold separately) before lifting. Using second person to stabilize load, slowly raise Saddle by depressing Pedal with your foot until Saddle is fully raised. 5. Insert Locking Pin (11) fully through the hole in the saddle and the base to secure the stand in the up position. [. . . ] We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTy IS exPReSSLy IN LIeU OF ALL OTHeR WARRANTIeS, exPReSS OR IMPLIeD, INCLUDINg THe WARRANTIeS OF MeRCHANTABILITy AND FITNeSS. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. [. . . ]