User manual CISSELL 36BS30

[. . . ] The warranty period on each new replacement part furnished by Cissell in fulfillment of the warranty on new equipment or parts shall be for the unexpired portion of the original warranty period on the part replaced. With respect to electric motors, coin meters and other accessories furnished with the new equipment, but not manufactured by Cissell, the warranty is limited to that provided by the respective manufacturer. Cissell's total liability arising out of the manufacture and sale of new equipment and parts, whether under the warranty or caused by Cissell's negligence or otherwise, shall be limited to Cissell repairing or replacing, at its option, any defective equipment or part returned f. o. b. Cissell's factory, transportation prepaid, within the applicable warranty period and found by Cissell to have been defective, and in no event shall Cissell be liable for damages of any kind, whether for any injury to persons or property or for any special or consequential damages. [. . . ] Under no circumstances should machine be operated until hot. Always keep the trap clean and in good working condition. When machine is on the end of a line of equipment, extend headers at least 4 ft. Install globe valve, union, check valve trap and optional by-pass of a line. Insulate steam supply and return line for safety of operator and safety while servicing machine. Repair or replace any worn or defective parts. beat the end Page 7 PANEL ASSEMBLY FOR FABRIC PRESSING HEADS Ref. P154 P153 P165 P454 P511 P512 P513 Description Single Table Top 33" Table Top 38" Table Top Table Leg, R or L Front Panel Asm. RC344 TU4934 TU2846 TU2847 P274 Description 1/4 - 20 Ph. of 6) * Consists of Front Panel, Cissell Nameplate, screws, and washers. Note: For servicing, new design allows easy access from front of machine by removing front panel screws. Nuts are welded to table leg. Page 8 PANEL ASSEMBLY FOR NON-FABRIC PRESSING HEADS Ref. P228 P260 P299 P542 P267 P266 WITH VACUUM Description Pedal 3/8" x 7 1/2" Black Pipe Flange Adapter (Vacuum) 2/3 - 3/4" Union - NPT Flange (Vacuum) Flange (Regular) (See separate page) (See separate page) Pedal Rod & Yoke Ass'y. Pedal Bearing Wrench (1/8") P255 P36 Page 12 CENTRAL AIR VACUUM VALVE &UPSTREAM VALVE SINGLE OR DOUBLE PARTS P368 P543 P548 P544 P546 Central Air Vacuum Valve - Consists of Ref. (No Vacuum) - Consists of 8-10 & 14-27. (No Vacuum) - Consists of 8-10 & 14-27. (With Vacuum) - Consists of 1-11, 14-16, & 18-27. (With Vacuum) - Consists of 1-11, 14-16, & 18-27. Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 Part No. P301 P226 P246 P244 P223 P252 P232 OP547 V15 P237 P371 ** P254 ** SF49 Description Rubber Tubing w/Spring Valve Seat Valve Seal w/Stem Spring (Pkg 6) Valve Body Hose Adapter Rubber Tubing 3/4" - 16 x 1/4" Lock Nut Small Lock Nut (Pkg. of 6) Pivot Support Bracket Pedal Rod Yoke Assembly Ref. K361 K362 P236 P536 P372 Description Single Valve Body NPT w/Union Double Valve Body NPT w/Union Copper Gasket (Pkg. Support Bracket * 20 21 22 23 24 25 * 26 28 P695 V05 P33H P126 V345 P375 P238 K605 "O" Ring Large Pack Nut Spring Retainer 1/4" - 20 x 1" Aln St Scr. [. . . ] To set spring into position, a dimension of about 3/4" should be maintained. After 3/4" is established, tighten set screw securely. Reinstall pivot, lock nut, pedal rod, pin, and cotter pin. Establish pedal clearance of 1-5/8" from the floor. [. . . ]