User manual CISSELL CF 220

[. . . ] - Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance. - WHAT TO DO IF YOU SMELL GAS · · · · · Do not try to light any appliances. Do not touch any electrical switch; do not use any phone in your building. Clear the room, building, or area of all occupants. [. . . ] Never exceed 0. 3 inches water column (. 8 mbar) static pressure in the exhaust duct without a booster fan. Inside surface of the duct must be smooth. Recommend pop rivets for duct assembly. MAKE-UPAIR FOR BEST DRYING: 1. Provide opening to the out-of-doors in accordance with the following: For each dryer-- 8 inches (204 mm) diameter exhaust requires 2 square feet (. 1858 m²) make-up air. 12 inches (305 mm)diameter exhaust requires 4 square feet (. 3716 m²) make-up air. Use barometric shutters in the inlet air opening to control air when dryers are not running. Other Recommendations To assure compliance, consult local building code requirements. Troubleshooting Hot dryer surfaces, scorched clothes, slow drying, lint accumulations, or air switch malfunction are indicators of exhaust duct and/or make-up air problems. OTHERRECOMMENDATIONS TROUBLESHOOTING Page 30 RULES FOR SAFE OPERATION OF DRYER RULES FOR SAFE OPERATION OF DRYER 1. Be sure your dryer is installed properly in accordance with the recommended instructions. CAUTION Be safe--shut main electrical power supply and gas supply off externally before attempting service. CAUTION Never use drycleaning solvents: gasoline, kerosene, or other flammable liquids in the dryer. This process will remove any films or residual coatings left by the manufacturing process. CAUTION Synthetic solvent fumes from dry cleaning machines create acids when drawn through the dryer. These acid fumes cause rusting of painted parts, pitting of bright plated parts and completely removes the zinc from galvanized metal parts, such as the tumbler basket. If the dry cleaning machines are in the same area as the tumbler, then the tumbler make-up air must come from a source free of solvent fumes. ABOVE 2, 000 FEET (610 M) ELEVATIONS ABOVE 2, 000 FEET (610 M) Input ratings shown on the rating plate (serial tag) are for elevations up to 2, 000 feet (610 m). For elevations above 2, 000 feet (610 m), rating should be reduced at a rate of 4% for each 1, 000 feet (305 m) above sea level. Page 32 OPERATING INSTRUCTIONS--TWO TIMER MODELS Page 33 OPERATING INSTRUCTIONS--TWO TIMER MODELS OPERATING INSTRUCTIONS--TWO TIMER MODELS OPERATINGINSTRUCTIONS--TWO TIMERMODELS 1. After loading the dryer with the water washed clothes load, close the loading door. For better drying, do not load dryer with combination of garments that twist. Turn the 60-minute drying timer to the desired drying time. The drying cycle light will be on and indicate the drying. The light shuts off when drying time is complete. Turn the 15-minute cooling cycle timer to the desired cool down time. [. . . ] Handle Trim Kickplate Page 60 DMP SENSOR ASSEMBLY Ref. TU15538 1 2 3 4 5 6 7 Part No. Description DMP Thermostat Assembly Bracket Switch - 220 degrees Thermistor Screw, #8-32 Nut, hex brass #8-32 Screw, #6-32 Nut, hex brass #6-32 TU15537 EA-00411-0 TU11991 M262 TU3266 TU3624 TU3400 Page 61 2 TIMER SENSOR ASSEMBLY Ref. No. Part No. Description TU6029 - Thermostat Assembly 1 2 3 TU2477 TU2486 TU3801 Thermostat #AR594 Bracket Nut, speed #C18784-010-4 Page 62 PRO SENSOR ASSEMBLY Ref. ESA-00940-0 Description Sensor Assembly Thermistor Thermostat Switch, 220 Degrees Screw, Mach. [. . . ]