User manual CISSELL CF 441

[. . . ] 1-5025-21A Page 9 DESCENDING CISSELL CONVEYOR CEILING HEIGHT "A" 5- 12 '0 /" 5- 12 '3 /" 5- 12 '6 /" 5- 12 '9 /" 6- 12 '0 /" 6- 12 '3 /" 6- 12 '6 /" 6- 12 '9 /" 7- 12 '0 /" 7- 12 '3 /" 7- 12 '6 /" 7- 12 '9 /" 8- 12 '0 /" 8- 12 '3 /" 8- 12 '6 /" 8- 12 '9 /" "B" 7-" '3 7-" '6 7-" '9 8-" '0 8-" '3 8-" '6 8-" '9 9-" '0 9-" '3 9-" '6 9-" '9 1'0 0-" 1'3 0-" 1'6 0-" 1'9 0-" 1'0 1-" "C" 10'-4 1/2" 10'-7 1/2" 10'-10 1/2" 11'-1 1/2" 11'-4 1/2" 11'-7 1/2" 11'-10 1/2" 12'-1 1/2" 12'-4 1/2" 12'-7 1/2" 12'-10 1/2" 13'-1 1/2" 13'-4 1/2" 13'-7 1/2" 13'-10 1/2" 14'-1 1/2" "D" 7- 12 '1 /" 7- 34 '5 /" 7-0 '1" 8'-2 1 4 /" 8'-6 1 2 /" 8'-10 3/4" 9-" '3 9- 14 '7 /" 9'-11 1/2" 10'-3 3/4" 1'8 0-" 10'-0 1/4" 11'-4 1/2" 11'-8 3/4" 1'1 2-" 12'-5 1/4" MINIMUM OVER GARMENTS MINIMUM LINKS 7-" '3 7-" '6 7-" '9 8-" '0 8-" '3 8-" '6 8-" '9 9-" '0 9-" '3 9-" '6 9-" '9 1'0 0-" 1'3 0-" 1'6 0-" 1'9 0-" 1'0 1-" 1'9 7-" 17'-7 3/4" 18'-0 1/2" 18'-5 1/4" 18'-10" 18'-8 3/4" 19'-1 1/2" 19'-6 1/4" 19'-5" 19'-9 3/4" 20'-2 1/2" 20'-7 1/4" 20'-6" 20'-10 3/4" 21'-3 1/2" 21'-2 1/4" 39 39 40 41 42 42 43 44 44 45 46 47 47 48 49 49 ALL SUPPORTS TO FLOORS FURNISHED WITH CONVEYOR. CUSTOMER TO BRACE TO RIGID PART OF BUILDING IF REQ'D. 8-2-72 1-5025-35 Page 10 1/4 HP 1/2 HP 3/4 HP 1/4 + 1/4 HP 1/2 + 1/2 HP No's Are For Links Are For Adder No's. Floor Model "F" Conveyor "P" Plain (Straight) 14-70 71-100 102-150 152-200 "L" Ell Shape 22-50 1 51-70 2 "L" Ell Shape w/Idlers 71-100 3 102-150 3+7 152-200 3+8 Double Deck "M" (No's. Are For Links Both Decks) Conveyor "P" Plain (Straight) 30-200 202-300 7 302-400 8 "L" Ell Shape w/Idlers 50-200 3 202-300 3+7 302-400 3+8 Up & Down "O" or Descending "Q" Conveyor "P" Plain (Straight) 29-100 102-120 21 122-200 8 "L" Ell Shape w/Idlers 39-80 3A 81-100 3A + 21 102-180 3A + 8 "P" Plain (Straight) 41-100 21 102-150 8 "L" Ell Shape w/Idlers 51-80 3A + 21 81-150 3A + 8 Page 11 CONVEYOR TRACK LUBRICATION Put vaseline (or light grease) in bottom of roller track to lubricate p t o r l e s A s a p yl b i a tt t po t a ta a lc r e . lo pl urcn o o f rc t l uvs A narrow strip of lubrication, about 1/8" in diameter and placed along the center of the roller path for about 1 foot at 5 foot spacings, will be picked up and spread by the rollers. [. . . ] Repeat every six months or when track surface becomes dry. A properly lubricated track will provide quiet roller operation and g e t ye t n t eo e a i gl f . ral xed h prtn ie Page 12 LINK ASSEMBLIES MODEL 5 Links 6 Links 8 Links 9 Links 10 Links 11 Links 12 Links 13 Links 14 Links 15 Links 5 Links 6 Links 8 Links 9 Links 10 Links 11 Links 12 Links 13 Links 14 Links 15 Links 5 Links 6 Links 8 Links 9 Links 10 Links 11 Links 12 Links 13 Links 14 Links 15 Links C1755 C1756 C1758 C1759 C1750 C1900 C1901 C1902 C1903 C1752 C1765 C1766 C1768 C1769 C1760 C1904 C1905 C1906 C1907 C1762 C1775 C1776 C1778 C1779 C1770 C1908 C1909 C1910 C1911 C1772 FLOOR Type B Link Assembly Type B Link Assembly Type B Link Assembly Type B Link Assembly Type B Link Assembly Type B Link Assembly Type B Link Assembly Type B Link Assembly Type B Link Assembly Type B Link Assembly Type N Link Assembly Type N Link Assembly Type N Link Assembly Type N Link Assembly Type N Link Assembly Type N Link Assembly Type N Link Assembly Type N Link Assembly Type N Link Assembly Type N Link Assembly Type S Link Assembly Type S Link Assembly Type S Link Assembly Type S Link Assembly Type S Link Assembly Type S Link Assembly Type S Link Assembly Type S Link Assembly Type S Link Assembly Type S Link Assembly OVERHEAD Type N Link Assembly Type S Link Assembly LINKS C1761 C1771 1 Link 1 Link Page 13 Link Assemblies No. o f Links Link Assemblies 140 150 160 170 180 190 200 210 220 230 240 250 260 270 280 290 300 310 320 330 340 350 360 370 380 390 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 9 10 5 6 5 5 5 8 8 10 10 10 15 9 15 15 15 10 10 10 10 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 6 6 8 9 10 8 9 8 9 10 6 8 8 9 10 8 8 10 10 15 8 8 8 9 10 15 10 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 5 8 9 8 9 8 9 10 10 10 6 6 8 9 10 5 6 5 5 15 10 8 10 10 10 15 10 6 6 6 8 9 6 9 8 9 10 6 6 580 590 600 610 620 630 640 650 660 670 680 690 700 710 720 730 740 750 760 770 780 790 800 810 820 830 840 850 860 870 880 890 900 910 920 930 940 950 960 970 980 990 1000 6 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 8 9 10 5 6 5 6 15 8 9 9 10 10 15 6 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 6 6 8 8 8 8 9 9 10 6 8 8 9 10 6 6 5 6 15 10 9 10 10 10 15 10 15 15 15 15 15 15 15 15 15 15 15 15 15 8 5 6 8 8 6 8 8 9 10 6 6 8 9 10 5 6 5 6 15 8 9 9 10 10 6 6 6 8 8 8 8 9 9 10 Page 14 CONVEYOR CAPACITY All straight track must add up to an even number of feet. Allow one (1) link per foot of straight track in any conveyor. The following number of links should be allowed for these turns: Any Drive End or Return End 90º Turn Complete 45º Riser 5 Links 10 Links 12 Links J-BOLT ASSEMBLY C2210 J-Bolt Assembly This assembly is used on all model conveyors. CONVEYORS WITH TURNS All overhead conveyors use C1071 Idler End. Floor model conveyors with turns use C167 Return End with Idler. For all straight floor model conveyors with single drive end use C169 Return End. Floor with turns 810 garments up get Idlers on all turns and ends. Up & down with turns 810 garments up get heavy duty idlers on turns and drive end. Turns can be butted directly into 45º track bends but straight track must be provided to adjust for overlap in links elsewhere in the conveyor. Page 15 OVERHEAD Maximum Power Strut length: 8' - 0" Preferred 10' - 0" Maximum CONVEYORS Power strut is spliced together with a C2191 strut splice. C310 C227 C217 C143 C228 C129 FB124 C189 C249 TU2814 FB124 C125 OP265 TU3604 C139 C1337 Description 3/8"-24 Castle Nut 13/16" Washer Ball Bearing (2 req'd. ) Retaining Ring Sleeve Spacer Bearing Housing 5/16"-18 x 1 1/4" Hex Head Cap Screw Idler Wheel 5/16"-18 Hex Nut 5/16" Split Lockwasher 5/16"-18 x 1 1/4" Hex Head Cap Screw Link Sprocket Support 3/8-16 x 1/2 Set Screw Cotter Pin Retaining Ring Sprocket Shaft Page 34 Manual Reversing Switch for Drive End w/Ground C1501 Ref. C1034 C1341 F566 C1365 C170 02-6081-221 C1515 F876 C257 TU3218 M261 C1199 Description Reversing Switch Manual Control Bracket 1/4" - 20 x 1/2" Allen Set Screw Straight Connector Plastic Bushing 5/16" Flexible Conduit (55" Long) 4 Wire Low Voltage Cable Assembly 90º Elbow Connector Conduit Strap #8-32 x 7/16 Self Drilling Screw #8-32 x 1/4 Self Taping Screw Handle, F/Reverse Page 35 Manual Reversing Switch for Return End w/Ground C1500 Ref. C1034 C1341 F566 TU2334 TU2335 TU2878 C1365 C170 02-6081-221 C1514 M261 C1199 Description Reversing Switch Manual Control Bracket 1/4" - 20 x 1/4" Allen Set Screw Junction Box Junction Box Cover #10 x 5/8" Sheet Metal Screw Straight Connector Plastic Bushing 5/16" Flexible Conduit (28" Long) 4 Wire Low Voltage Cable Assembly #8-32 x 1/4 Self Taping Screw Handle, F/Reverse Switch Page 36 Manual Reversing Switch for Idler End w/Ground C1504 Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Part No. C1034 C1341 F566 TU2334 TU2335 TU2878 C1365 C170 02-6081-221 C1516 C257 TU3218 M261 C1199 Description Reversing Switch Manual Control Bracket 1/4" - 20 x 1/4" Allen Set Screw Junction Box Junction Box Cover #10 x 5/8" Sheet Metal Screw Straight Connector Plastic Bushing 5/16" Flexible Conduit (42" Long) 4 Wire Low Voltage Cable Assembly Conduit Strap #8-32 x 7/16 Self Drilling Screw #8-32 x 1/4 Self Taping Screw Handle, F/Reverse Switch Page 37 WARRANTY The Cissell Manufacturing Company (Cissell) warrants all new equipment (and the original parts thereof) to be free from defects in material or workmanship for a period of one (1) year from the date of sale thereof to an original purchaser for use, except as hereinafter provided. With respect to non-durable parts normally requiring replacement in less than one (1) year due to normal wear and tear, including, but not limited to, cloth goods, valve discs, hoses, and iron cords, and with respect to all new repair or replacement parts for Cissell equipment for which the one (1) year warranty period has expired, or for all new repair or replacement parts for equipment other than Cissell equipment, the warranty period is limited to ninety (90) days from date of sale. The warranty period on each new replacement part furnished by Cissell in fulfillment of the warranty on new equipment or parts shall be for the unexpired portion of the original warranty period on the part replaced. With respect to electric motors, coin meters and other accessories furnished with the new equipment, but not manufactured by Cissell, the warranty is limited to that provided by the respective manufacturer. Cissell's total liability arising out of the manufacture and sale of new equipment and parts, whether under the warranty or caused by Cissell's negligence or otherwise, shall be limited to Cissell repairing or replacing, at its option, any defective equipment or part returned f. o. b. Cissell's factory, transportation prepaid, within the applicable warranty period and found by Cissell to have been defective, and in no event shall Cissell be liable for damages of any kind, whether for any injury to persons or property or for any special or consequential damages. [. . . ] The liability of Cissell does not include furnishing (or paying for) any labor such as that required to service, remove or install; to diagnose troubles; to adjust, remove or replace defective equipment or a part; nor does it include any responsibility for transportation expense which is involved therein. The warranty of Cissell is contingent upon installation and use of its equipment under normal operating conditions. The warranty is void on equipment or parts; that have been subjected to misuse, accident, or negligent damage; operated under loads, pressures, speeds, electrical connections, plumbing, or conditions other than those specified by Cissell; operated or repaired with other than genuine Cissell replacement parts; damaged by fire, flood, vandalism, or such other causes beyond the control of Cissell; altered or repaired in any way that effects the reliability or detracts from its performance, or; which have had the identification plate, or serial number, altered, defaced, or removed. No defective equipment or part may be returned to Cissell for repair or replacement without prior written authorization from Cissell. [. . . ]