User manual CISSELL CSHW75-HF245-304

[. . . ] Contents 1 General safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Technical data and dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The temperature, water level and wash action remain the same as programmed. During the wash cycle, this function remains active until the START button (S) is pressed again. During intermediate spin : The intermediate spin normally lasts 1 minute. By activating function F1, the machine will spin for nine minutes unless the START button (S) is pressed earlier. During final spin : At final spin, you have high spin after low spin. By activating F1 during low spin, this low spin will be extended to15 minutes unless the START button (S) is pressed earlier. If the 15 minutes of low spin have been completed, the high spin is automatically canceled. By activating F1 after the preprogrammed low spin, you will have a maximum of 14 minutes of high spin unless the START button (S) is pressed earlier. Adjustable stop time : Here you can program a certain stop time. The display shows the countdown of this extra time. When this time is expired, the function will appear automatically and the program will continue. The stop time can be programmed by means of the ECO button (E). By pressing it once, the stop time is programmed for 10 minutes. From now onwards, "F1" and "10" appear by turns on the middle display. By pressing the ECO button (E) once more, you add each time 10 minutes. By means of the START button (S), you can each time reduce 10 minutes. Remark : The programmed stop time is executed after the decimal point in the right display has extinguished. The stop time cannot be programmed during spin. Function F2 (soak) This function can only be chosen during prewash, main wash and first rinse. The bath is filled till high water level and heated up to 40 °C (if a higher temperature was programmed, this will be followed). As long as this temperature is not reached, the machine makes a reduced wash action ( shorter action time and longer pause time). When the bath has reached its temperature, the drum will make one left/right rotation every 4 minutes. Should the temperature fall, the water will be heated again, during which the action will be reduced again. [. . . ] E3 (Eprom) The Eprom is wrong, replace it by another. Remark : For coin op machines, it is possible that a program number appears on the right display in combination with E3. This indicates a wrong price adjustment for this program. A coin value "0" or bigger than "1000" was programmed. Example : wrong price adjustment for program 5. E4 (water level) The appropriate water level was not reached after 15 minutes. E5 (Heating) The wash bath did not reach the required temperature after 80 minutes of heating. E6 (door lock) The door lock was released during the wash cycle. E7 (safety level) The water was insufficiently drained, the machine did not spin and the water is possibly still inside the tub. E8 (temperature sensor) The temperature sensor is probably broken or malfunctioning. 21 6 E9 (motor protection) The thermo-magnetic protection was activated 5 times. EA (tilt) The tilt switch was activated 15 times during final spin and the final spin was therefore skipped. Eb (tilt switch) The tilt switch is blocked. Mot 2 ( rotation sensor) The speed detection is not operating properly. [. . . ]