User manual CISSELL FMMAN58

[. . . ] FM Form Finisher Models FMCD FMGG FMFC / FMJC / FMLM FMMM MANUAL OWNER'S MANUAL CISSELL MANUFACTURING COMPANY HEADQUARTERS 831 SOUTH FIRST ST. BOX 32270 LOUISVILLE, KY 40232-2270 PHONE: (502) 587-1292 SALES FAX: (502) 585-3625 SERVICE/PARTS FAX: (502) 681-1275 MANUAL THIS MANUAL MUST BE GIVEN TO THE EQUIPMENT OWNER. MAN58 5/96 Page 1 WARRANTY The Cissell Manufacturing Company (Cissell) warrants all new equipment (and the original parts thereof) to be free from defects in material or workmanship for a period of one (1) year from the date of sale thereof to an original purchaser for use, except as hereinafter provided. With respect to non-durable parts normally requiring replacement in less than one (1) year due to normal wear and tear, including, but not limited to, cloth goods, valve discs, hoses, and iron cords, and with respect to all new repair or replacement parts for Cissell equipment for which the one (1) year warranty period has expired, or for all new repair or replacement parts for equipment other than Cissell equipment, the warranty period is limited to ninety (90) days from date of sale. [. . . ] If form is still too low. . . or too high. . . repeat adjustment until it is correct. PROBLEM: Revolving Form rides too high above base. TO CORRECT: Loosen F286 Bearing Lock Nut. Turn F287 Bearing Adjustment Screw CLOCKWISE. CHECK ADJUSTMENT: Replace revolving form on base. If perfectly adjusted, form will rotate freely and snugly on felt seal around top of base. If form is still too high. . . or too low. . . repeat adjustment until it is correct. Page 17 AIR DAMPER LINKAGE ADJUSTMENT 1. See that the air damper is closed (position shown below). Blower air pressure will hold it closed. Check to see that the pins in the air solenoid lever and air damper lever are located as shown below. Loosen the set screw in the air damper lever hub and, with the damper closed, rotate the lever until the air solenoid armature gap is 7/8". Tighten the air damper lever set screw slightly. Check to see that there is slight end play of the levers on the air damper shaft so they may rotate freely. NOTE: If the damper does not open in a positive manner, reconnect the lower end of the damper opening spring to the alternative connection position shown below. AIR PRESSURE SETTING ADJUSTMENT 1. Adjust the air damper linkage as described above. Loosen the set screw in the damper wire swivel. Move the air pressure control lever on top of the control enclosure to minimum setting. With the blower motor running and the air damper closed, move the air pressure lever until it touches the pin in the lower end of the air damper lever. Tighten the damper wire set screw onto the damper wire tightly. Page 18 ALVE STEAM VALVE LINKAGE ADJUSTMENT 1. With steam solenoid lever resting against lever bumper, loosen the set screw in the lever hub. Set the steam valve extension bar at the angle shown (approximately 100º off centerline of steam solenoid lever) and retighten set screw. Adjust position of steam valve adjusting nuts to obtain 1/16" pull rod gap at the valve lever and lock adjusting nuts together. The steam valve must be touching the lever bumper. Page 19 FOOT ASSEMBLY FOOT PEDAL SWITCH ASSEMBLY - F1178 INSTALLA ALLATION INSTALLATION INSTRUCTIONS FOR AF 177 SWITCH 1. [. . . ] Inspect damper control wire, levers and pressure control lever. Be sure that all parts are connected and adjusted according to instructions. Repair or replace any defective parts. 7F Defective air solenoid 7G Defective air solenoid linkage 7H Damper plate stuck 7I Improper air operating lever assembly (8) Relief damper "flaps" 8 Stretched damper springs (9) Auto air won't stop 9A Defective air timer 9B Defective air relay 9C Defective air solenoid 9D Broken or stretched damper opening spring (10) Bag won't inflate to garment size 10A Pressure setting too low 10B Pressure control defective Page 38 PROBLEM (10) Bag won't inflate to garment size (Con't. ) CAUSE CAUSE 10C Bag size levers not properly set 10D Bag improperly installed on frame REMEDY Move the sizing levers until the bag is properly sized. Refer to bag installation instructions and check to see that bag strings ane untangled and properly connected. [. . . ]