User manual CISSELL MANCONS

[. . . ] Cissell Sensi-Form CISSELL MANUFACTURING COMPANY HEADQUARTERS 831 SOUTH FIRST ST. BOX 32270 LOUISVILLE, KY 40232-2270 PHONE: (502) 587-1292 SALES FAX: (502) 585-3625 SERVICE/PARTS FAX: (502) 681-1275 THIS MANUAL MUST BE GIVEN TO THE EQUIPMENT OWNER. MANCONS 8/00 IH WARRANTY The Cissell Manufacturing Company (Cissell) warrants all new equipment (and the original parts thereof) to be free from defects in material or workmanship for a period of one (1) year from the date of sale thereof to an original purchaser for use, except as hereinafter provided. With respect to non-durable parts normally requiring replacement in less than one (1) year due to normal wear and tear, including, but not limited to, cloth goods, valve discs, hoses, and iron cords, and with respect to all new repair or replacement parts for Cissell equipment for which the one (1) year warranty period has expired, or for all new repair or replacement parts for equipment other than Cissell equipment, the warranty period is limited to ninety (90) days from date of sale. [. . . ] After adjusting lock the controls by twisting the knobs clockwise. Press the AIR foot switch to operate the blower for sizing the form bag. Size the bag by adjusting the DAMPER CONTROL. Using the Control Panel, press the MODE SELECT until the AIR light glows and press START/CANCEL to operate the blower, then proceed with sizing the bag. Set the three control timers to the recommended settings: Steaming: 6-9 seconds Conditioning: 4-9 seconds Drying: 12-16 seconds These settings should be fine-tuned to the particular garment, steam pressure and ambient conditions. The recommended cycle is the steam/air conditioning and the drying. The control will power up in this cycle. This machine has the ability to pre-steam a garment prior to the automatic finishing cycle. To actuate this cycle, press the MODE SELECT pad until the PRE-STEAM LIGHT glows, then press START. If a cycle is operating, it can be cancelled at any time by pressing any foot switch or control panel pads. Control Panel Page 5 OPERATION - CONTROLS Page 6 SERVICE CHART CAUTION: BEFORE SERVICEING MACHINE, SHUT OFF ELECTRICAL POWER TO AVOID POSSIBLE ELECTRICAL SHOCK. SHUT OFF STEAM SUPPLY AND PURGE PRESSURE FROM STEAM LINES TO AVOID BURNS FROM HOT STEAM. REFER TO PARTS SHEETS FOR CORRECT REPLACEMENT PARTS. (1) No Steam PROBLEM A. Electric power off. CAUSE C. Bad solenoid valve coil. D. Steam timer may slip on shaft and be set on 0. (2) No Air See A. Defective motor relay. Open valve in steam supply line. Check for blown fuse, tripped circuit breaker or loose wire connection. Disconnect power and measure coil resistance. A good coil should be between 50-125 hms. Replace coil if not within these parameters. Turn shaft to maximum counter-clockwise position. Attach knob to shaft pointing to 0 and tighten set screw. [. . . ] 1 2 3 4 5 6 7 8 9 10 11 12 13 Part No. F11 F24 F842 F1319 F1427 ---- Description Ref. 13 14 15 16 17 18 19 20 21 22 23 24 25 Part No. RC344 TU2846 AF130 SB180 F1265 TU2947 TU2814 AF131 MTR297 C363 FG226 C249 F1463 Description 1/4 - 20 x 3/4 Screw 1/4 Lockwasher Motor Mounting Hardware Junction Box Cover Lower Rear Cover 1/4 Flat Washer 5/16 Lockwasher Motor Mounting Bracket Motor, 115-230/50-60/1 5/16 x 1-1/4 Bolt Inlet Cone 5/16 Hex Nut Angle Seal Sleever (11) Sleever (24) Vent Clamp Screen Retainer Filter Control Panel (see separate page) F1238 Base Top TU7733 #8 x 1/2 Screw F1203 Base Bottom F1290 Rear Jacket F1264 Fan Housing FG292 Blower Wheel RC344 1/4 - 20 x 3/4 Screw Page 16 MS. [. . . ]