User manual CITATION 50 AV CONTROLLER

[. . . ] 5. 0 A/V Controller Owner's Manual ® Staple or clip your original bill of sale here. ¤ 2 Table of Contents Introduction . 9 Front Panel Controls & Indicators . 46 Setting the Balance and Level Trims . 59 More on next page 3 Table of Contents (continued) Troubleshooting Guide . [. . . ] Using the < or > Menu Control buttons , adjust the sound level so that it is equal to the level just set at the Left Front speaker. This may be done either by careful listening or with a sound pressure level meter, but use of the meter is strongly recommended to achieve the most accurate match. It is important that the output level for all channels be made with the < or > Menu . When they are used, you will see the reference offset indication that appears below the speaker position icon change to a positive or negative number. DO NOT use the main system Volume Control to adjust anything other than the Left Front channel when the reference level is being established. Note: System Configuration Control button Once the Center speaker's level has been matched to the reference, press the ¤ Menu Control button again and the test noise will move to the Right Front speaker. Repeat the adjustment procedure as explained above until the output level is equal to the previous two speakers. After adjusting the Right Front speaker, press the ¤ Menu Control button to move to the first available surround speaker. Make the adjustment and continue to use the ¤ Menu Control button to move to each succeeding speaker when complete. After one adjustment of all speakers, including any subwoofers that are connected to the system, repeat the process one more time to double-check that all speakers have an equal output level. Once you are satisfied that all speakers output the test noise at an equal level, press the ¤ Menu Control button until < Spkr Setup Menu < is highlighted at the top of the screen, and press the < Menu Control button to return to the main Speakr Setup menu. If no further speaker setup or calibration adjustments are required, press the ¤ Menu Control button one more time so that < Main Menu < is highlighted at the top of the screen and press the < Menu Control button to return to the Main Menu. Program Setup The Citation 5. 0 may be programmed with up to twelve separate program profiles, each of which may combine any of the audio and video inputs along with various source controls. Once these profiles are established, they may be assigned to either the "Watch" or "Listen" menus, or both, for easy selection. The 5. 0 is shipped with factory defaults for program profiles as shown in Appendix A, but these generic choices may be edited to suit the specific need of your system as shown below. To modify the individual program profiles to suit your system preferences and signal sources, press the Menu button and note that the Main Menu (Figure OSD-3) appears. Press the ¤ Menu Control button six times until the words Program Setup are highlighted on the screen. Next, press the > Menu Control button to go to the Programs Menu (Figure OSD-8). Programs Se ain Menu < ram 1 L o Input A t Level + t Balance A o Input C o Detect A Display O ggers On N M g e i u u e e tup < P N A I I V V O T r a u n n i i S r o m d p p d d D i D 1 0 U O U N O analog 0 TO MP-1 TO NE Figure OSD-8 37 The second line, just below the line indicating how to return to the "Main Menu, " contains the program number. Remember that this number only defines the sources and conditions that you attach to it in the following steps. It DOES NOT refer to any specific input connection on the 5. 0's rear panel. System Configuration Before proceeding it is a good idea to have a chart of which input sources are connected to each of the rear panel inputs. This will speed the installation process. A worksheet for this purpose is contained in Appendix B. It is also a good idea to review the factory default settings, as they may provide a starting point from which to model your system. To select a program to customize, press the ¤ Menu Control button so that Program is highlighted. [. . . ] Digital Mode Status display for Dolby Digital. Customize Surround Mode menu for analog sources. Customize Surround Mode menu for digital sources. Reset Accomplished message. 73 FPD-3 FPD-4 FPD-5 FPD-6 OSD-19 OSD-20 OSD-21 OSD-22 OSD-23 OSD-24 OSD-25 OSD-26 OSD-27 OSD-28 OSD-29 OSD-30 OSD-31 OSD-32 OSD-33 OSD-34 OSD-35 OSD-36 OSD-37 OSD-38 OSD-39 OSD-40 Limited U. S. [. . . ]