User manual CITIZEN WATCH 087

[. . . ] 6 F B 8 0 2 4 24 6 4 OF A 3 7 8 M 9 ON 6 M AL 12 AL 2 C 1 M C HR T E M C AL E GS IN WARN T ST E L CHR A M OP CHARG 5 18 E 7 M C AL T IMPORTANT Before using When the watch does not operate according to the instruction manual, it is insufficiently charged. Charge the secondary battery of the watch for more than 6 hours, approximately 20cm (8in. ) away from the fluorescent or incandescent lamp (30W) as light sources. When charging the secondary battery, do not put it too close to the light source. * When charging the watch under direct rays of the sun, charge for more than an hour. FEATURES This watch is a multi-hands analog solar watch with alarm and chronograph functions, and a solar power function as its base which provides the power source for the watch's hands movement and alarm sound by converting solar energy into electrical power with the solar cell fitted on its face. English BEFORE USING A secondary battery is used in this watch to store electrical energy. [. . . ] Switching the Alarm ON and OFF Each time button A is pressed in the alarm mode, the alarm switches ON and OFF. Alarm Sound Monitor On the alarm mode (button M in normal position), pressing button A will sound the alarm for 5 seconds. NOTE · There may be some variation in the volume of the alarm sound, depending on how much the secondary battery is charged. · The alarm sound volume gets rather lower in the displays other than the time display (calendar, alarm, chronograph, "0" position confirmation, and each display's adjustment state). Once the alarm time has been set, use the watch normally in time display mode. USING THE CHRONOGRAPH Chronograph measurement is taken in 1/20 (0. 05) seconds and can continue for 60 minutes max. Over 60 minutes, the watch enters the chronograph reset state. Chronograph Chronograph reset Function hand measurement (Chrono minutes or chrono 1/20 sec. ) OF F 8 2 8 2 6 4 6 4 OF F B 0 A 0 M AL ON M AL ON 7 GE AL AL 7 CHAR M CHR T M CHR T CAL CAL ST OP C E L CHR A T SE ING WARN M E L CHR A T SE ING WARN Reading the Chronograph Hands · Second hand (Chronograph seconds) 20 · Function hand Chrono minutes or chrono 1/20 seconds. * The function hand moves every one minute. Pressing button B while in chrono stop or split display, switches the function hand to show chrono 1/20 seconds. Second hand Chrono second hand. ST OP M M CHAR GE ME ME M CAL T M CAL T 21 C A Reset Start A Stop Pressing button A to repeat the chronograph start and stop cycle. Chronograph Measurement Chronograph standard or accumulated elapsed time measurement 1. Press button M to set the mode hand to <CHR> and get the chronograph display. At this time, the second hand and the function hand will return to the "0" position. * The hour, minute and 24-hour hands show the present time. 3 While pressing button B continuously, the function hand switches to 1/20 (0. 05) second hand measurement, so read the value at that time. When button B is released, the function hand resumes showing chronograph minutes. While the chronograph is stopped state, pressing button C resets the function hand and the second hand to the 0 position. 2. Each time button A is pressed, it repeatedly starts or stops the chronograph, along with a confirmation sound. How to read each chronograph hand if the measured time when the chronograph is stopped is over 1 minute 1 Read the number of minutes with the function hand 2 Read the number of seconds with the second hand 22 23 Chronograph Split Measurement Pressing button C during chronograph measurement causes the chronograph split time to appear on display with a beep for confirmation. Press button C again, the next chronograph split time is displayed, along with a confirmation sound. The split time display is automatically cancelled after about 10 seconds, and the chronograph returns to the measurement state. During either chronograph split time display or measurement, pressing button A causes the chronograph stop to appear on display. In the chronograph stop state, pressing button C causes the chronograph reset. * During split time measurement or Automatically cancelled after C while split time display, each time about 10 seconds you press button C the next split time is displayed. [. . . ] Generally, your watch is not affected by magnetic fields from such household appliances as television sets and stereo equipment. Static electricity The integrated circuits used in the watch are sensitive to static electricity. If exposed to intense static electricity, the watch's display may lose its accuracy. 6. Avoid harmful chemicals, solvents and gases Avoid wearing your watch in the presence of strong chemicals, solvents and gases. [. . . ]