User manual CITIZEN C2201-PD

[. . . ] Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage to the product. Slots and openings on the back or bottom of the case are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, do not block or cover these openings. [. . . ] Turn off the power, and return the auto cutter blade to its home position by turning the emergency knob of the auto cutter in the direction indicated by the arrow. With tweezers or similar, totally remove remaining paper from the cutter blade area. Emergency Knob 4. 7 FEED Switch Function Press the feed switch to feed the paper, cut it, and output the cut portion. 4. 8 Paper End Function If the printing paper runs out, the parallel interface will output BUSY, FAULT, and PE to the host, and the serial interface will output DTR to stop printing, respectively. If some data are still remaining in the buffer, printing will be resumed after replacing the paper. Replace the paper according to "4. 3 Inserting the Paper. " After replacing the paper, cancel BUSY (DTR), FAULT, and PE outputs. For details, see "4. 10 Near Paper End Function. " 21 CITIZEN C2201-PD User's Manual 4. 9 Connecting the PHU (Paper Holding Unit) 1. Plug the connector cable of the optional PHU into the CN5 on the control PCB. When plugging it, pay attention to its insertion direction. Connector for PHU CN5 4. 10 Paper Near End Function (When Using the PHU) If the paper is running out, the PNE sensor informs the host computer that the paper is running out. You can adjust the printable amount left after PNE has been detected, up to about50 of paper roll. Loosen the screw and slide the PNE sensor position forward or backward. When you slide the PNE sensor away from the paper roller, the printable amount left after PNE has been detected will be increased. DS1- 1 2 3 4 5 6 7 8 Function Auto cutter CR switching Printing density DTR-DSR/XON-XOFF Baud rate and parity setting Baud rate and parity setting Baud rate and parity setting Baud rate and parity setting See Table 1. ON Enabled LF operation OFF Disabled Ignored Upon Shipment ON OFF OFF OFF OFF OFF OFF OFF Combination with DS2-6. XON-XOFF DTR-DSR DIP switch 2 (DS2) No. 1 2 3 4 5 6 Function PNE function Reserved Reserved Auto-loading Paper selection Print density ON Enabled OFF Disabled Upon Shipment Enabled Normal thermal paper 7 Data length ON 8 Not used ON * With the type U model (North American type), the DIP switches marked are set to OFF. Table 1 DS1-8 OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON Disabled Dedicated thermal paper (Black mark) Combination with DS1-3. 8 Bits 7 Bits ON· ON ON ON ON ON Baud rate and parity setting DS1-7 OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON DS1-6 OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON DS1-5 OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON Interface Parallel input Serial input Parity Baud Rate -- None Odd Even -- 1, 200 bps 2, 400 bps 4, 800 bps 9, 600 bps 19, 200 bps 1, 200 bps 2, 400 bps 4, 800 bps 9, 600 bps 19, 200 bps 1, 200 bps 2, 400 bps 4, 800 bps 9, 600 bps 19, 200 bps 25 CITIZEN C2201-PD User's Manual Table 2 DS1-3 OFF OFF ON ON Print density DS2-6 OFF ON OFF ON Print Density Light Standard Dark Darker Level 0 1 2 3 26 CITIZEN C2201-PD User's Manual 6. 6. 1 PARALLEL INTERFACE Specifications · Data input system · Control signals · Applicable connectors : 8-bit parallel (DATA0 to DATA7) : ACK, BUSY, STROBE, FAULT, PE, RESET : Printer side Cable side : 57LE-40360 (Anphenol) or its equivalent : 57-30360 (Anphenol) or its equivalent 6. 2 Connector's Pin Configuration No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 STROBE DATA 0 DATA 1 DATA 2 DATA 3 DATA 4 DATA 5 DATA 6 DATA 7 ACK BUSY PE Signal Name No. 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Signal Name TWISTED PAIR GND RESET FAULT FRAME GND 27 CITIZEN C2201-PD User's Manual 6. 3 6. 3. 1 Input and Output Signals Input and Output Signals (1) Input signals to the printer · DATA · STROBE · RESET · ACK · BUSY · FAULT · PE : 8-bit parallel signal (Active: "High") : Strobe signal to read the 8-bit data (Active: "Low") : Signal to reset the entire printer (Active: "Low"); 1 ms or more (2) Output signals from the printer : 8-bit data request signal. (Active: "Low") : Signal to indicate that the printer is busy. (Active: "High") : Turned to "Low" when the printer has an alarm. At this time, all the control circuits in the printer stop. [. . . ] · The download bit image thus defined remains effective until redefinition, ESC @ execution, ESC &, or power OFF takes place. [Caution] · A download character and a download bit image can not be defined simultaneously. With this command executed, defined content of a download character is cleared. · Relations between the bit image data and the dot defined are shown below: GS / [See Also] 76 CITIZEN C2201-PD User's Manual [Sample Program] GOSUB IMG LPRINT CHR$ (&H1D) + "/" + CHR$ (0) ; LPRINT CHR$ (&H1D) + "/" + CHR$ (1) ; LPRINT CHR$ (&H1D) + "/" + CHR$ (2) ; LPRINT CHR$ (&H1D) + "/" + CHR$ (3) ; END IMG : n 1 = 10 : n 2= 5 LPRINT CHR$ (&H1D) + "" ; LPRINT CHR$ (n1) + CHR$ (n2) ; FOR J=1 TO n18 FOR I=1 TO n2 LPRINT CHR$ (J) ; NEXT I NEXT J RETURN [Print Results] 77 CITIZEN C2201-PD User's Manual GS / m Printing the Download, Bit Image <1D>H<2F>H<m> {0 m 03} Data is described in Hex code. Prints download bit image in a mode specified by m. [. . . ]