User manual CITIZEN C350

[. . . ] * Do not place this product on an unstable cart, stand of table. The product may fall, causing serious damage to the product. * Slots and openings on the cabinet and the back or bottom are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, do not block or cover these openings. [. . . ] Paper roll Ribbon cassette AC adapter User's manual (1 roll) (1 unit) (1unit) (1 booklet) CITIZEN 1 iDP3110 User's Manual 2. TYPE CLASSIFICATIONS 2. 1 Type The product is categorized according to the naming plan indicated below. iDP3110 24 40 P R J F 120 230 A B iDP3110 24 P J 120 A Model Name Number of columns 24 : 24 columns/144 dots 40 : 40 columns/180 dots Printer cover A : 60mm(Dia. ) Paper roll B : 80mm(Dia. ) Paper roll Power source 120 : AC 120V 230 : AC 220-240V Interface P : Parallel (Centronics) R : Serial (RS-232C) Character J : Japanese F : International 2. 2 AC adapter Please use the exclusive adapter indicated below. 90AD-U (AC 120V) 90AD-E (AC 220-240V) CITIZEN 2 iDP3110 User's Manual 2. 3 Specifications Item 1 Printing method 2 Printing direction 3 Character configuration (W × H) 4 Number of columns per line 5 Printing speed 6 Character size (W × H) 7 Line pitch 8 Paper 9 Interface 10 Ribbon cassette iDP3110-24* Dot matrix One-way printing (5 + 1) × 8 iDP3110-40* (4 + 0. 5) × 8 11 Voltage 12 Power consumption 13 Weight 14 Dimension 15 Operating temp. 16 Storage temp 24 columns: 144 dot/line 40 columns: 180 dot/line Approx. 1. 6 × 2. 4 mm 1. 08 × 2. 4 mm 3. 52 mm Paper Roll 57. 5 ± 0. 5(W) × 60 (Dia) mm 57. 5 ± 0. 5(W) × 80 (Dia) mm Type P: Parallel Interface (Centronics) Type R: Serial Interface (RS-232C) Exclusive ribbon cassette Purple print : IR-91P Black print : IR-91B (Option) DC 7V ± 1V (Printing) Use exclusive adapter (DC 7V, 1. 2A) Printing : approx. 400g 106(W) × 180(D) × 88(H) mm (60 Dia. Paper Roll) 106(W) × 180(D) × 106(H) mm (80 Dia. Paper Roll) 0°C to 40°C -20°C to 60°C CITIZEN 3 iDP3110 User's Manual 3. EXTERNAL APPEARANCE AND PART DESCRIPTION 3. 1 External Appearance CITIZEN 4 iDP3110 User's Manual 3. 2 Part Descriptions 1. SEL Lamp Insert the output plug of the AC adapter attached. ACK is issued at the end of the BUSY signal (negative logic) - BUSY Signal indicating the printer is busy. Input new data when the signal is in "LOW" condition. (positive logic) - SELECT Signal indicating the printer is set to a selected condition (on-line). "HIGH" state signifies the printer is selected. (3) Others - GND - FG The common circuit ground. Equivalent to "case ground". · Input [ Printer side ] [ Host side ] DATA : 74HC373 equivalent STB : 74HC14 equivalent RESET : 74HC04 equivalent CITIZEN 12 iDP3110 User's Manual · Output [ Printer side ] [ Host side ] (4) Timing chart 1) Timing for data entry and printing T1 T2, T3 T4 0. 5 µs MIN 1 µs MIN 2 µs TYPE (5) Data receiving Printer is capable of accepting data from the host while the BUSY signal is in the "LOW" state. Printer cannot accept data when the signal is "HIGH". CITIZEN 13 iDP3110 User's Manual 6. SERIAL INTERFACE 6. 1 Specifications 1) Synchronization 2) Baud rate 3) Word configuration : Asynchronous : User selection, 4, 800; 9, 600 Baud / sec : Start bit 1 bit : Data bit 8 bit : Stop bit More than 1 bit 4) Signal polarity RS-232C * Mark = Logic "1" (-3 to ­12V) * Space = Logic "0" (+3 to +12V) TTL(RESET) * H level = Logic "1" (refer to (3), section 6. 3) * L level = Logic "0" 5) Input control (DTR signal) * Mark : Data transmission not possible * Space : Data transmission possible CITIZEN 14 iDP3110 User's Manual 6. 2 Connector Pin Assignment SIGNAL SIGNAL PIN NAME 1 FG 7 GND 3 RD 20 DTR 23 RESET SIGNAL DIRECTION HOST-PRINTER FUNCTION Frame ground Signal ground Received data Printer BUSY signal Printer reset signal RS232C TTL Note: 1. Signals for RS-232C are based on EIA RS-232C level. Applicable connector (D-Sub connector) Printer : 17LE-13250 (Anphenol equivalent) Cable : 17JE-23250 (Anphenol equivalent) 6. 3 Description of Input / Output Signal (1) I / O signals 1) RD Serial input data signal. Data is ignored when framing error, overrun error, or parity error has occurred. 2) DTR Input command or data while this signal is in ready state. [. . . ] However, if a new pattern is registered in an address already in use, existing data is cleared and the newly entered data becomes valid. If more than 8 characters are registered, all existing character registration is cleared. [Address setting] Specified address is matched to the character code and can be accessed likewise to the stored fixed character record. If a fixed character is defined in the specified address, the fixed character becomes invalid. [. . . ]