User manual CITIZEN CBM-291

[. . . ] LINE THERMAL PRINTER MODEL CBM-290/291 User's Manual CBM-290/291 User's Manual Declaration of Conformity This printer conforms to the following Standards: Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/31/EEC, 93/68/EEC. LVD : EN60950 EMC : EN55022 Class A EN61000-3-2 EN61000-3-3 EN55024 This declaration is applied only for 230V model. Warning: This is a Class A products. In a domestic environment this product may cause radio intereference in which case the user may be required to take adequate measures. CITIZEN is a registered trade mark of CITIZEN WATCH CO. , LTD. , Japan CITIZEN es una marca registrada de CITIZEN WATCH CO. , LTD. , Japón CITIZEN CBM-290/291 User's Manual IMPORTANT SAFETY INSTRUCTIONS · · · · · · Read all of these instructions and save them for later reference. Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning. Do not place this product on an unstable cart, stand or table. [. . . ] Eliminating slack on the printing paper and close the front panel. Feed paper by pressing Feed switch, if necessary. Factory setting is Head up position. Make sure to pull head up lever forward to pull down printer mechanism, Because auto paper feed can not be carried out at had up condition. When any print data is remaining us print buffer, printer stars printing automatically after loading paper. 10 CITIZEN CBM-290/291 User's Manual Make sure to pay attention to the followings. 1. In case that the paper is bent or the paper is not fed properly, set print head at head up condition and remove the paper carefully by turning paper feed knob. For replacing roll paper, set print head at head up condition, and remove the paper which remains in printer unit carefully by turning paper feed knob. 11 CITIZEN CBM-290/291 User's Manual 3. 7 Removing paper jam and canceling cutter lock Remove paper jam or cancel cutter lock by following the procedure explained below. (1) Open front cover (2) Put mechanism lock lever inside of main body, pull down printer mechanism. When paper remains inside of printer, remove this paper. (3) Removing paper jam Remove paper jam manually with care. To pull out the paper from printer mechanism, pull it out carefully at head up condition. (4) Canceling cutter lock Remove paper inside of paper cutter and turn ON power. In case cutter blades to home position and carries out initializing, cutter lock was cleared completely. In case cutter does not return to home position or occurs some error again, turn OFF power, turn the knob which locates on left bottom side of auto cutter to the front side as shown in the below, then return cutter blade manually and remove the paper inside of auto cutter. (5) After fixing the problem, pull down head up lever and return printer mechanism to its home position. Cautions : Since print head and motor are hot, do not carry out this action right after printing. For removing the remaining paper, do not touch the surface of print head and motor. 12 CITIZEN CBM-290/291 User's Manual 3. 8 Self print function By supplying power as pushing FEED switch or send RESET signal to this printer, type of characters which is used, ROM version and DIP switch setting etc are automatically printed. For CBM-291, paper is automatically cut off after this self printing. 3. 9 PE and Mechanical alarm 3. 9. 1 Paper end (PE) This sensor detects the existence of paper. Printer stops printing when roll paper runs out, outputs BUSY and PE signal and lights up PAPER lamp. When new roll paper is set, this signal is canceled and PAPER lamp lights off. And then, printer starts printing and becomes data waiting status. When any print data is remaining in print buffer, make sure that printer starts printing the data after new roll paper is set. 3. 9. 2 Mechanical alarm This printer stops printing, stops supplying motor and print head with power and outputs BUSY signal and FAULT (in Parallel interface) signal to host computer, when the motor of printer mechanism is locked, auto paper cutter is locked, or temperature of print head is getting high. In this case, turn OFF power supply and clear the problem. To make printer stand-by mode, turn ON power supply after clearing the problem. Make sure that the data which is stored in the buffer is to be cleared due to power supply is turned OFF. [. . . ] (GS :) (37) Starting / Ending Macro Definition Code : [1D]h + [3A]h Specifying starting / ending macro definition. · · Maximum content available for macro definition is 2048 bytes. A portion exceeding 2048 bytes is not defined. Even with ESC @ (initialization of the printer) having been executed, defined content is not cleared. [. . . ]