User manual CITIZEN CBM-510

[. . . ] · Unplug this product from the wall outlet before cleaning. · Do not use this product near water. · Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage to the product. [. . . ] [Caution] · When "m" is beyond a definition range, no signal is output, discarding "n1" and "n2". · The drawer drive duty must be within the following range: ON time ON time + OFF time (The OFF time should be 4 times or more longer than the ON time. ) [Default] [Sample Program] LPRINT CHR$(&H1B) + "p"; LPRINT CHR$(0); Selects pin No. LPRINT CHR$(5); Sets ON time to 10ms LPRINT CHR$(50); Sets OFF time to 100ms END The initial value for "m", "n1" and "n2" is not defined. 0. 2 -- 91 -- ESC t n [Function] [Code] [Range] [Outline] Selecting the character code table <1B>H<74>H<n> 0 n 9, n = 255 Selecting the character code table: The character code table is selected based on the value of "n". n 0 1 2 3 4 5 6 7 8 9 255 Character Code Table Codepage PC437 (USA, European Standard) Codepage Katakana (Japanese) Codepage PC850 (Multilingual) Codepage PC860 (Portuguese) Codepage PC863 (Canadian-French) Codepage PC865 (Nordic) Codepage PC852 (Eastern Europe) Codepage PC866 (Russian) Codepage PC857 (Turkish) Windows Codepage Space Page(For user setting) [Default] [See Also] [Sample Program] This is a character code table specified with DIP Switch. CHARACTER CODES TABLE" LPRINT CHR$(&H1B) + "t" + CHR$(0); LPRINT "n"=0; FOR C=&HB2 TO &HB5 LPRINT CHR$(C); NEXT C LPRINT CHR$(&HA); LPRINT CHR$(&H1B) + "t" + CHR$(9); LPRINT "n"=9; FOR C=&HB2 TO &HB5 LPRINT CHR$(C); NEXT C LPRINT CHR$(&HA); END n=0 n = 0 [Print Results] n= 9 23'µ n = 9 -- 92 -- ESC { n [Function] [Code] [Range] [Outline] Specifying/Canceling the inverted characters <1B>H<7B>H<n> 0 n 255 Specifying/canceling inverted characters. · "n" is valid only for the lowest bit (n0). · Control by the lowest bit (n0) is shown as follows: n0 0 1 Condition Canceling inverted characters. Specifying inverted characters. [Caution] · Inverted printing means printing the line turned 180°. · This command is valid only when it is specified at the beginning of a line. · This command does not affect the PAGE MODE. [Default] [Sample Program] n=0 LPRINT CHR$(&H1B) + "{" + CHR$(0); LPRINT "AAAAA" + CHR$(&HA); LPRINT "BBBBB" + CHR$(&HA); LPRINT CHR$(&H1B) + "{" + CHR$(1); LPRINT "AAAAA" + CHR$(&HA); LPRINT "BBBBB" + CHR$(&HA); END < AAAAA BBBBB Inversion Specified Inversion Canceled Paper Feed Direction [Print Results] -- 93 -- AAAAA BBBBB GS !n [Function] [Code] [Range] Specifying the character size <1D>H<21>H<n> 0 1 1 [Outline] n 255, where: 8, 8 vertical magnification horizontal magnification Specifies the character size (Vertical and horizontal magnification). Bit 0 1 2 3 4 5 6 7 Function Value Hex. · Once defined, the download bit image remains effective until redefinition, ESC @ execution, ESC &, or power OFF takes place. [Caution] · Relations between the bit image data and the dots defined are shown below. · A download character and a download bit image cannot be defined simultaneously. With this command executed, the defined content of a downloaded character is cleared. [See Also] GS / n1 × 8 dots d1 dn2 + 1 d2 dn2 + 2 n2 × 8 dots dn2 × 2 + 1 dn2 × 2 + 1 MSB LSB dn2 dn2 × 2 dn2 × n2 × 8 -- 97 -- [Sample Program] GOSUB IMG LPRINT CHR$(&H1D) + "/" + CHR$(0); LPRINT CHR$(&H1D) + "/" + CHR$(1); LPRINT CHR$(&H1D) + "/" + CHR$(2); LPRINT CHR$(&H1D) + "/" + CHR$(3); END IMG: n1=10 : n2=5 LPRINT CHR$(&H1D) + " "; LPRINT CHR$(n1) + CHR$(n2); FOR J=1 TO n1 8 FOR I=1 TO n2 LPRINT CHR$(J); NEXT I NEXT J RETURN * * [Print Results] NORMAL MODE DOUBLE WIDTH MODE DOUBLE HEIGHT MODE QUADRUPLE MODE -- 98 -- GS ( A pL pH n m [Function] [Code] [Definition] Execution of test printing <1D>H<28>H<41>H<pL><pH><n><m> (pL+(pH × 256))=2 (pL=2, pH=0) 0 1 [Outline] n m 2, 48 3, 49 n m 50 51 Specified test printing will be executed. · pL, pH will specify the number of subsequent parameters by (pL+(pH × 256))bytes. · n will specify the paper for test printing in the following table. n 0, 48 1, 49 2, 50 Category of paper Basic paper (Paper rolls) Paper rolls · m will specify the category of test printing in the following table. m 1, 49 2, 50 3, 51 Category of test printing Hexadecimal dump Printer's status printing Rolling pattern printing [Details] · This command is only valid when processed at the head of a line during the STANDARD MODE. · The command will be ignored in PAGE MODE. · During macro definition, if this command is processed, the macro definition is suspended, and the command starts being processed. · Printer will reset its hardware after finishing test printing. Therefore, the printer makes download characters, bit map images and macros undefined, clears the reception buffer/print buffer, and returns the various settings to defaults. At this time, the DIP switches are read again. · Paper cutting is performed at the end of test printing. [. . . ] Wenn die Steuerung per DTR/DSR nicht aktiviert ist, ignoriert der Computer dieses Signal und sendet Daten an den Drucker. Dieses Signal kann auch als Rücksetzungssignal nach Ändern der DIP-Schalterstellung verwendet werden (siehe 5. 2 "DIP-Schaltertabelle"). Wenn die Pulsbreite des Signals 1 ms oder länger beträgt, wird eine Rücksetzungssignal übertragen. (5) INIT Dieses Signal kann als Rücksetzungssignal verwendet werden, nachdem Sie die Stellung des entsprechenden DIP-Schalters geändert haben (siehe 5. 2 "DIPSchaltertabelle"). [. . . ]