User manual CITIZEN CBM-820

[. . . ] TERMINAL SLIP PRINTER MODEL CBM-820 User's Manual Declaration of Conformity This printer conforms to the following Standards: Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/31/EEC, 93/68/EEC. LVD EMC : : : : : EN60950 EN55022 EN61000-3-2 EN61000-3-3 EN55024 Class B This declaration is applied only for 230V model. CITIZEN is a registered trade mark of CITIZEN WATCH CO. , LTD. , Japan CITIZEN es una marca registrada de CITIZEN WATCH CO. , LTD. , Japón ESC/POS and TM-295 are trademarks of SEIKO EPSON CORPORATION Auto Side LoadingTM is a trademark of Star Micronics Co. , Ltd. Windows codepage is a registered trademark of Microsoft Corporation IMPORTANT SAFETY INSTRUCTIONS · Read all of these instructions and save them for future reference. · Follow all warnings and instructions marked on the product. · Unplug this product from the wall outlet before cleaning. [. . . ] · n denotes the number of columns from the head of the line to the horizontal tab setting position. n is equal to the setting column position - 1, and if the horizontal tab is to be set in the 9th column, for example, set n = 8. · k denotes the number of horizontal tab positions to be set. · The tab position is set to the position at a distance of the character width × n from the head of the line. This character width includes the right space size of the character, and if double width is selected, the character width will be doubled. A horizontal magnification selection is followed even in the page mode. · The data, <n>k, which denotes a setting position is input in the ascending order and ends with <00>H. · ESC D NUL clears all the set tab positions. · If the data <n>k is equal to or smaller than the preceding data <n>k-1, it is assumed that horizontal tab setting has been finished. If this is the case, the subsequent data will be processed as normal one. · Up to 32 tab positions can be set. The data exceeding this limit is processed as normal data. · If HT is executed, a move to the tab position beyond the print area will be made to the position of the print area + 1 dot. · Even if the character width is changed after setting the horizontal tab position, the latter will not change. · There are two kinds of right space sizes of the characters; for the standard mode and page mode. To set the horizontal tab position in the respective modes, set the right space size of the characters in the very mode you are in. Every 8 characters of the 5 × 7 font (9th, 17th, 25th character, and so on) HT [Caution] [Default] [See Also] ­ 54 ­ ESC F n [Function] [Code] Selects/Deselects Ejection of Single Sheet in Reverse Direction ASCII Hexadecimal Decimal 0 n 255 ESC F 1B 46 27 70 n n n [Range] [Outline] This command selects or deselects single sheet ejection in the reverse direction with FF. · n is valid only for the least significant bit. At n = < 1>B, the command selects reverse directional ejection. At n = < 0>B, the command deselects reverse directional ejection(selects forward directional ejection). n=0 FF [Default] [See Also] ESC J n [Function] [Code] Print and Paper Feed ASCII Hexadecimal Decimal 0 n 255 ESC J 1B 4A 27 74 n n n [Range] [Outline] This command prints the data in the print buffer and feeds the paper by n/60 inch. Since the printer has the minimum paper feed pitch of 1/144 inch, a paper feed amount of n/60 inch is treated as follows: · For the standard mode: The paper is fed by an approximate value of INT((6n+5)+0. 5)/72 inch. [. . . ] Ein Umstellen der Speicherschalter kann zu Funktionsstörungen des Druckers führen. ­ 123 ­ 6. Schnittstelle Dieser Anhang enthält detaillierte Spezifikationen für die Standardeinstellung der Druckerschnittstelle. 13 25 14 1 6. 1 Stifte und Signalnamen StiftNr. 1 2 3 4 Signal Richtung name FG TXD RXD RTS ­ OUT IN OUT Gehäuseerdung Übertragungsdaten Empfangsdaten ESC/POS-Modus Identisch mit DTR-Signal Nicht angeschlossen IN · DIP-Schalter 9 = OFF Speicherschalter 4-5 im DTR/DSR-Datenaustauschmodus = 0 zeigt an, ob der Datenempfang vom Hauptrechner aktiv oder inaktiv ist. SPACE: Empfang aktiviert MARK: Empfang deaktiviert Dieses Signal wird im X-ON/X-OFF-Datenaustauschmodus nicht überprüft. [. . . ]