User manual CITIZEN CBM-920II

[. . . ] DOT MATRIX PRINTER MODEL CBM920II User's Manual WEEE MARK En Ge Fr Sp It Du Da Por Pol Declaration of Conformity This printer conforms to the following Standards: Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/31/EEC, 93/68/EEC. LVD : EN60950-1 EMC : EN55022 EN61000-3-2 EN61000-3-3 EN55024 Class A This declaration is applied only for 230V model. IMPORTANT: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference. CAUTION: Use shielded cable for this equipment. Sicherheitshinweis Die Steckdose zum Anschluß dieses Druckers muß nahe dem Gerät angebracht und leicht zugänglich sein. For Uses in Canada This Class A digital apparatus complies with Canadian ICES-003. [. . . ] The printer prints "Hexadecimal Dump" and then stops. The printer prints data sent from the host by converting it to hexadecimal code. If the data received last is less than one line, press the FEED switch to print the received data. Print data for one line differs depending on the specification (number of digits). Example of Self-print: Example of Hexadecimal print: -- 20 -- 4. 9 Memory Switch Setting <Memory Switch Initial Setting> NO. Item 0 International character selection 1 2 3 4 5 6 7 8 9 A B C D E Code page selection Emulation selection Ack timing *2 Communication error data processing *3 Paper-near-end selection Power ON state Busy signal clear timing *1 Input buffer size PE output at PNE *2 Communication data bit length selection *3 I/F, LED state at PNE BUSY at FEED switch ON Auto loading Clear after auto loading Supply voltage check Paper lamp Japan (920JPN) Japanese 920 emulation (Japan) International (920Intl) U. S. A 920 emulation (International) CBM920 emulation After clearing BUSY (After) Replace with 7Fh (7Fh) Valid Online CBM-920 2k bytes Valid 8 bits I/F+LED Invalid Valid (short) FEED SW Only at power ON CBM920 emulation *1: Effective only for parallel I/F (P model). *2: Applicable to parallel I/F (P model). *3: Applicable to serial I/F (R model). Memory switch setting can be changed by a command or by manual operation. a) Change by command Memory switch can be changed by a command. When the printer receives the command, it outputs a BUSY signal and enters memory setting mode. After writing into memory switch, software resetting is carried out and the receive buffer/print buffer are cleared causing each set value to return to the initial value and then the contents of the memory switch(es) are reloaded. Use care when changing two or more set values. -- 21 -- b) Change by manual operation Set the DIP switch (SW1) No. Turn the printer power on while pressing and holding the FEED switch. The printer prints the information on the current memory switch setting and then enters the Change Setting mode. In this case, the PAPER lamp and the POWER lamp blink alternatively at 1second intervals and the BUSY signal is outputted. Using the FEED switch, choose one of the options for each setting item. Changing setting item A total of 15 setting items are available. The printer prints the contents of setting items and current set values on print paper. Pressing the FEED switch short causes the setting item to move. When all the setting items are changed, the re-setting state or writing (registering) to memory switch state is reached. To change the value of setting item, press and hold the FEED switch for more than 1 second. Current set value is printed with a mark "?". Changing options When item to be selected in the setting items is specified, current option is printer with a mark "?". When selecting an option, press the FEED switch short. [. . . ] The DC2 (12H) code is assigned to the command with another meaning. -- 46 -- 2. iDP3110 emulation In order to reduce power consumption when printer is not in operation, two power down modes triggered by the codes DC2 (12H) and DC3 (13H) are available with this printer. When the printer receives DC2 (12H) or DC3 (13H), it enters the power down mode after all data previously received is printed out. To exit the power down mode, re-enter the printer power or apply the "LOW" signal to the RESET terminal for more than 4 ms. (a) DC2 (12H) The printer enters the power down mode when DC3 (13H) code is entered. [. . . ]