User manual CITIZEN CH-403C

[. . . ] · Self measurement is no therapy!In no case may you change the dosage of medication prescribed by your physician. · In operation for blood pressure measurement, you should urinate and should remain relatively still for 10 to 15 minutes prior to measurement. [. . . ] · If blood pressure is measured repeatedly, an accurate result will not be achieved. An interval of about 10 minutes should be allowed. · The memory is erased if the batteries are removed for replacement, etc. and a record should be kept of any necessary data. Precautions for maintenance · Do NOT store the blood pressure monitor where it will be exposed to direct sunlight, high temperature (over 60°C), low temperature (below ­20°C), high relative humidity (over 95%) or in a dusty place. · Do NOT expose the blood pressure monitor to under force or vibration, or drop it. · Remove the battery/batteries when not in use for a long period. · Do NOT disassemble the apparatus. · Do NOT bend the cuff or air hose unnecessarily. · NEVER wipe the blood pressure monitor with thinner or benzene, as they may damage it. · When the monitor is very dirty, wipe it clean with a cloth moistened with Sterilizing alcohol or a neutral detergent, and then wipe it with a dry cloth. Do NOT use thinner or benzene. Nature and frequency of maintenance: This products is designed for use over an extended period of time; however, it is generally recommended that it be inspected every two years to ensure proper function and performance. - Eng 4 - Protect the nature environment: Please help protect natural environment by respecting national and/or local recycling regulations when disposing of the batteries and the products at the end of their useful lives. Manufacturer: Name: Address: Premier Precision Ltd. Block E, G-H, 6 th floor, Phase 2, Yip Fat Factory Building, 73-75 Hoi Yuen Road, Kwun Tong, Kowloon, Hong Kong English Reference European standard: This products complies with EC instructions 93/42/EEC (Medical Device Directive) and with the following standards: EN 1060-1: 1995 "Noninvasive Sphygmomanometers, Part 1 General Requirements" and EN 1060-3: 1997 "Noninvasive Sphygmo-manometers, Part 3 Supplementary Requirements for Electromechanical Blood-Pressure Measuring Systems". European Representative: Name: Address: WvW elektronische Geräte Vertrieb GmbH. Robert-Koch-Straße 20, D-80538 München, GERMANY MEASUREMENTS 1. Turn power ON CH-40 3C SELECT MEMO RY START POWE R Insert the Hose plug from the cuff into the hose socket at the mainframe until it is tightly connected. Press the "Power switch" for power ON. - Eng 5 - SYSTOLIC mmHg DIASTOLIC mmHg SYSTOLIC mmHg DIASTOLIC mmHg AVE. 1 2 3 4 5 6 7 PULSE/min AVE. 1 2 3 4 5 6 7 PULSE/min All display marks appear for approx. 1 second and buzzer beeps. SYSTOLIC mmHg DIASTOLIC mmHg SYSTOLIC mmHg DIASTOLIC mmHg AVE. 1 2 3 4 5 6 7 PULSE/min Ready for measurement AVE. 1 2 3 4 5 6 7 PULSE/min After all display marks are disappeared, deflation mark "w" appears for approx. 1 second (three short beeps notify you of ready for measurement) then the last pressure setting value appears for approx. [. . . ] Memory recall CH-40 3C SYSTOLIC mmHg DIASTOLIC mmHg AVE. SELEC T MEMO RY START POWE R 1 2 3 4 5 6 7 PULSE/min · By a second depressing of "Memory Recall Switch", the value for latest (last measured value) blood pressure is displayed. The " ] " mark shifts to right (from "Ave. " to "1") and notify that the value is the last measured (newest one) value. SYSTOLIC mmHg DIASTOLIC mmHg This blood pressure monitor has a function which is able to display last measured value. · Press the "Memory Recall Switch" to recall the last measured blood pressure. [. . . ]