User manual CITIZEN CH-432B

[. . . ] Measurement should be made regularly at the same time each day. · Do NOT be impressed by the results of one measurement. Keep a record of blood pressure variations. · Emotional stress may tend to cause pressure to rise. [. . . ] and a record should be kept of any necessary data. Italiano Deutch Precautions for maintenance · Do NOT store the blood pressure monitor where it will be exposed to direct sunlight, high temperature (over 60°C), low temperature (below ­20°C), high relative humidity (over 95%) or in a dusty place. · Do NOT expose the blood pressure monitor to under force or vibration, or drop it. · Remove the battery/batteries when not in use for a long period. · Do NOT disassemble the apparatus. · Do NOT bend the cuff or air hose unnecessarily. · NEVER wipe the blood pressure monitor with thinner or benzene, as they may damage it. Français - Eng 3 - · When the monitor is very dirty, wipe it clean with a cloth moistened with Sterilizing alcohol or a neutral detergent, and then wipe it with a dry cloth. Do NOT use thinner or benzene. Reference European standard: This products complies with EC instructions 93/42/EEC (Medical Device Directive) and with the following standards: EN 1060-1: 1995 "Noninvasive Sphygmomanometers, Part 1 General Requirements" and EN 1060-3: 1997 "Noninvasive Sphygmo-manometers, Part 3 Supplementary Requirements for Electromechanical Blood-Pressure Measuring Systems". Nature and frequency of maintenance: This products is designed for use over an extended period of time; however, it is generally recommended that it be inspected every two years to ensure proper function and performance. Manufacturer: Name: Address: Premier Precision Ltd. Block E, G-H, 6th floor, Phase 2, Yip Fat Factory Building, 73-75 Hoi Yuen Road, Kwun Tong, Kowloon, Hong Kong Protect the nature environment: Please help protect natural environment by respecting national and/or local recycling regulations when disposing of the batteries and the products at the end of their useful lives. European Representative: Name: Address: WvW elektronische Geräte Vertrieb GmbH. Robert-Koch-Straße 20, D-80538 München, GERMANY - Eng 4 - IDENTIFICATION OF PARTS Tube socket Systolic blood pressure display section Diastolic blood pressure/ Pulse display section English Español Português CH -4 DI AS SY IC STOL mm Hg BT 32 B mm Hg TO LIC in E /m PULS Italiano STA POW ER RT Cuff tube Air connector Deutch Cuff Battry cover Power/Start switch Français - Eng 5 - MEASUREMENTS 1. Attaching of Arm Cuff and Posture During Measurement Wind the arm cuff around the left upper arm tightly so that bottom edge of the cuff is positioned about 1 ­ 2cm above the elbow joint. · When you will wind the cuff, please wind the cuff next to the skin of possible. (If measurement is made by rolling the shirts or jacket up over the arm, this will constrict the upper arm and prevent accurate measurement. ) · Cuff tube should be placed on the inside of your arm as figure. Unfasten and open the cuff as shown in the figure. · Please make sure that the cuff is fastened tightly. Note that uneven cuff winding will prevent proper measurements. - Eng 6 - 2. Carrying out the Measurement English Español Rest the elbow on a table so that the section of the upper arm is at the height of the heart. Relax the lower arm across the table and remain still, since movement - artifacts may falsify the measuring result. Make measurements in either a seated or reclining posture with the palm turned upward. Português Press the "POWER / START" switch. SYSTOLIC mmHg DIASTOLIC mmHg Italiano PULSE /min Deutch Français When the "POWER / START" switch is pressed, the lastmeasured systolic blood pressure and diastolic blood pressure are displayed for about 2 seconds. SYSTOLIC mmHg DIASTOLIC mmHg Insert the air connector from the cuff into the tube socket at the mainframe until it is tightly connected. PULSE /min At the first measurement after battery replacement the mark of "Q" is displayed for about 2 seconds. - Eng 7 - SYSTOLIC mmHg DIASTOLIC mmHg PULSE /min When the "POWER / START" switch pressing, the pressure level for measurement will change at optional level over 160 mmHg. But if the "POWER / START" switch is released before 160 mmHg, the pressure is heightened to 160mmHg. SYSTOLIC mmHg DIASTOLIC mmHg SYSTOLIC mmHg DIASTOLIC mmHg PULSE /min PULSE /min When the pressure lowers by 15mmHg after pressurization stops, the mark of "Q" is displayed. SYSTOLIC mmHg DIASTOLIC mmHg SYSTOLIC mmHg DIASTOLIC mmHg PULSE /min PULSE /min The pressure is automatically heightened to the level for measurement of the blood pressure based on the last-measured systolic blood pressure. At the first measurement after battery replacement the pressure is heightened to 160mmHg. If the level of the pressure is not enough, the pressure is automatically heightened to the level for measurement of the blood pressure again. If pulse is recognized, the pressure is shifted to the diastolic blood pressure indicating section and change over, synchronized with the pulse. - Eng 8 - SYSTOLIC mmHg DIASTOLIC mmHg Automatic Pressure Setting q This product automatically sets the pressure based on the previous measurement, so you can easily measure blood pressure by pressing one button without resetting the pressure for each measurement. If several people use the unit, we recommend using the manual settings as follows. English PULSE /min Español SYSTOLIC mmHg DIASTOLIC mmHg Manual Pressure Setting PULSE /min When the measurement has been completed, the systolic blood pressure, the diastolic blood pressure and the pulse rate are alternately displayed and the air is discharged. The systolic blood pressure and the diastolic blood pressure are displayed for about 2 seconds and the pulse is displayed for about 1 second. The measured data are registered automatically, as long as they are not error. [. . . ] Automatic Power OFF Function If the unit is left without any operation after measurement, an "Automatic Power-OFF Function" runs to turn off the power after approximately 3 minutes. To continue measurement, press the "POWER / START" switch again. Note: The memory data are erased when you replace the batteries. · The batteries that are included power the monitor. [. . . ]