User manual CITIZEN CLP-1001

[. . . ] E N G L I S H User's Manual CLP 1001, 2001 CLP 6001, 6002, 6401 CLP 7201e, 7202e E N G L I S H "DESIGNED AND MANUFACTURED TO BE EQUIVALENT TO EUROPEAN STANDARD FOR ITE, EN60950. " CE marking shows conformity to the following criteria and provisions: Low Voltage Directive (73/23/EEC)/EN60950 EMC Directive (89/336/EEC)/EN55022 & EN50082-1 The following symbols are used in this manual. E N G L I S H WARNING CAUTION Indicates a situation which, if not observed and handled properly, could result in death or serious injury. Indicates a situation which, if not observed and handled properly, could result in injury. For the safe operation of your printer, please read the following important operation and safety instructions carefully: 1. 3. Read all of these instructions and save them for later reference. Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning. [. . . ] This guarantees that the printer configuration is maintained even after the power is turned off. n Pause key: n Feed key: n Stop key: Selects the mode. Saves the selection contents and returns the printer to the normal operating mode. E N G L I S H The functions indicated by an character work on the CLP 1001, 2001, 6001, 6002 and 6401 printers. Those with a character work on the CLP 7201e and 7202e printers LCD Indication Transfer Peel OFF Cut OFF Tear OFF AfterPrt DirectTM Peel ON Cut ON Tear ON PeelWait TearBar AutoCut NoAction ContinuP Function Description Direct thermal or thermal transfer printing Enable or disable peeler function Enable or disable cutter function Enable or disable tear-off function "AfterPrint" functions. Set the operation of the printer after the label has been printed. Select media gap detection method either "edge" (label gap), reflective or continuous media Set the printhead temperature Set the print speed in inches/second Set the feed speed in inches/second Set the back feed speed in inch/sec Vertical label position adjustment. Stop position adjustment Settings Lock Off/On. When "on", causes the printer to ignore commands changing the above values set on the control panel. Edge Reflect HeadHeat PrintSpd Feed Spd Back Spd Vert Adj HorizAdj StopPos SetLckOF Heat 01 PSpeed 2 FSpeed 2 BSpeed 2 V-2. 00in H-2. 00in S-2. 00in SetLckON Heat 30 PSpeed 7 FSpeed 7 BSpeed 7 V+2. 00in H+2. 00in S+2. 00in E N G L I S H 2. 4 Self-Test Mode And Hex Dump The printer enters the self-test mode when the Feed key is pressed and held down while turning the printer on. If the Feed key is held down for more than four seconds, the printer assumes continuous media is installed. The printer performs a two-page self-test print then enters the Hex Dump or Data Dump mode (prints out the communication data by ASCII code). The printer returns to the normal operating mode only when the power is turned off. 2. 5 System Maintenance Mode The printer enters the system maintenance mode when the Pause, Feed and Stop keys are pressed and held down simultaneously while turning the printer on. The printer enters the communication parameter setting, system setups and paper gap and black line sensor sensitivity adjusting mode. The mode is selected with the Pause key and the mode item is selected with the Feed key. Changing of the contents is executed as soon as they are displayed on the screen. Pressing the Stop key returns the printer to the normal operating mode. LCD Indication 9600bps 19200bps 38400bps Function Description Select baud rate between 38, 400 bps down to 300 bps. Select 8 or 7 data bits Select Native Off or Native On mode. Select distance of media sensor relative to the printhead position. Cmnd RST 8 bits NativeOF fVirtual Cmnd STD 7 bits NativeON fReal Cmnd AS4 Select between standard command set, AS400 mode or raster mode. Select between fixed media and adjustable sensor when installed. See through or black line sensor checking mode. See Section 2. 6 AjSensOF PE x. xxV AjSensOn BL x. xxV 2. 6 Adjusting the sensors for different media The voltage setting mode, part of the system setting mode, is used to correctly adjust the see-through or black line sensors for the particular type of media being used in the printer. The ideal voltage is between 3. 0v and 3. 3v for both the PE (paper end or gap) and BL (black line) modes. [. . . ] Install the paper or check for mis-feed. Correct the faulty setting of the paper detection (paper gap, black line, continuous paper). Correct the faulty parameter for paper (max. Some settings can be adjusted on the printer but it is more likely the changes must be made on the host computer. [. . . ]