User manual CITIZEN CLP-4081

[. . . ] Do not use liquid or aerosol cleaners, thinner, trichloroethylene, benzine, ketone or similar chemicals. Instead use a damp cloth for cleaning, when the printer is disconnected from the mains supply. Do not use this product near water or where a chemical reaction can occur such as in a laboratory or where there is a lot of oil, dust, salt or iron particles. Do not place this product on an unstable cart, stand or table. [. . . ] (For details, see Chapter 2 Control Panel. ) 4. Cover hinges: The cover hinges are used to hold the cover as far as you have opened it. Control keys Hinge LCD LEDs CONNECTOR LOCATIONS 5 4 PCMCIA memory card cover 3 1 6 CLP 1001, 2001, 6001, 6002, 6401 (1) (2) (3) RS232C serial interface USB interface (CLP 7201e, 7202e only) Parallel Interface (4) (5) (6) CLP 7201e, 7202e Power switch AC power inlet (for mains power cord) PCMCIA memory card cover 1. 3 Connection to Power CAUTION Always use an AC outlet that accepts a three-pronged plug. Otherwise, static electricity may be generated and there will be danger of electric shock. E N G L I S H Connect to an AC outlet as follows: 1 2 3 Check that the power switch on the printer is set to OFF. Connect the connector of the power cord to the power inlet on the printer. Insert the plug of the power cord in the AC outlet. 1. 4 Connection to a Computer An interface cable is necessary for connecting the printer to a computer. To connect them, proceed as follows: 1 2 3 Turn off both power switches of the printer and the computer. Connect the connector of one end of the interface cable to the interface connector at the lower side of the printer and secure it correctly. Connect the connector of the other end of the interface cable to the interface connector on the computer and secure it correctly. Serial interface Serial interface USB interface Parallel interface Parallel interface CLP 1001, 2001, 6001, 6002, 6401 CLP 7201e, 7202e E N G L I S H Chapter 2 ­ The Control Panel 2. 1 Control Panel The control panel on the front of the printer consists of three control keys (Pause, Feed and Stop), two LED indicator lights (Power, Error) and a LCD message screen. On the left side of the control panel there are three adjustment controls (paper gap, black line and LCD contrast). (1) LCD: Displays the current printer status, configuration settings, or an error message. (2) LEDs: The green LED indicator shows that the power is turned on. The red LED lights when there is an error. Adjustment is made using the upper adjuster on the control panel. See section 2. 1 PE 3. 05v E N G L I S H Adjustment procedure for media with a black line on the reverse side: 1 2 Set the unmarked part of the media ­ the area without the black line - under the media sensor (see section 3. 4). Adjust the black line value on the control panel to a value between 3. 0 volts and 3. 3 volts. Adjustment is made using the middle adjuster on the control panel. See section 2. 1 BL 3. 05v 2. 6 Factory Default Settings To return the print to Factory Default settings, press and hold down the Pause, Feed and Stop keys simultaneously for more than four seconds whilst turning on the power. S Maint S/I Init The display will first show "S Maint" You must keep the buttons held down until the LCD displays the message "S/I Init" E N G L I S H Chapter 3 ­ Paper & Ribbon 3. 1 Media Installation CAUTION Take care not to trap lose clothing in the mechanism of the printer when it is closed!However, here is a Roll The printer is designed for easy loading of paper and ribbon. detailed guide for first-time users: 1 Push down the open lever to release the print head and lift it out of the way Push down the sensor arm lever to move the sensor arm out of the way (not present on the CLP 1001) Slide the black plastic media guide over the media support bar and insert the support bar through the roll of media being installed. 2 3 4 Rest the media support bar in to the paper holder and slide the roll guide to the width of the roll paper. The paper roll should be pushed against the side nearest the top cover hinges *, but should still be free to move easily. Place the media on the main printer chassis, with the left side of the media against the fixed paper guide . Slide the small moving paper guide to maintain the correct media width slightly in Roll paper contact the right edge of the media so that the paper does not skew. [. . . ] This generally requires someone with good technical knowledge of communication systems Pause key pressed or pause command received. Mechanism head open Paper out or paper end or a problem with feeding the media such as the printer cannot detect the end of the media. Press the Pause key once again to resume printing. If the Stop key is pressed, the stored printing contents will be lost and "on line" will turn on. [. . . ]