User manual CITIZEN CT-S310

[. . . ] This printer conforms to the following Standards: This declaration is applied only for 230V model. Company names and product names in this manual are trademarks or registered trademarks of relevant companies. IMPORTANT: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. [. . . ] Be careful that the paper cover does not entrap your hands or fingers. be careful with sharp edges on the printer. Don't allow them to injure you or damage property. May result in electric shock, burn, or injury. If the printer emits smoke, an odd smell, or unusual noise while printing, immediately abort the current print session and unplug the printer from the supply outlet. When cleaning the printer, always turn it off and unplug it from the supply outlet. Use a soft, dry cloth for cleaning the surface of the printer case. For severe stains, use a soft cloth slightly dampened with water. Never use organic cleaning solvent such as alcohol, paint thinner, trichloroethylene, benzene, or ketone. never use a chemically processed cleaning cloth. To remove paper chips, use a soft brush. When transporting the printer, remove the roll paper form its paper holder. The thermal head is at a dangerously high temperature immediately after printing. Allow it to cool off before launching maintenance work. The CT-S310 is a thermal line printer designed for use with a broad array of terminal equipment including, data, POS, and kitchen terminals. With extensive features, it can be used in a wide range of applications. When unpacking the printer, confirm that the following are provided: Printer: AC adapter (AC adapter type): AC power cord: Sample paper roll: Partition for 58-mm wide paper roll: User's manual (This manual): 1 1 1 1 roll 1 1 AC adapter (AC adapter type) Printer (AC adapter type) AC power cord Partition for 58-mm wide paper roll Sample paper roll Printer (Built-in power supply type) The printer models are classified by the following designation method: Power supply No marking: AC power type (built-in power supply) DC: DC power supply type Interface RS: Serial RS-232C compliant PA: Parallel IEEE 1284 compliant UB: USB Black mark sensor for back side None: No sensor M1: Left black mark sensor M2: Right black mark sensor Body case color WH: Cool white BK: Black Inducing ground(Character+AC power cord) J: Japan E: Europe U: North America 2 Model Classification) Print method Print width Dot density Print speed Number of print columns *2 ( ) shows the value with 58 mm wide paper. Line thermal dot print method 72 mm/576 dots, (48 mm/384 dots) *1 8 × 8 dots/mm (203 dpi) 150 mm/s (Fastest, print density level 0), 1200 dot lines/s Font A: 48/42 (32/30) columns; 12 × 24 dots Font B: 64/56 (42/40) columns; 9 × 17 dots Font C: 72/63 (48/45) columns; 8 × 16 dots Font A: 1. 23 mm (1/6 inch) Thermal paper roll: 80 -1 mm/58 -1 mm × 83 mm Paper thickness: 65-75 µm Serial (RS-232C compliant), Parallel (IEEE 1284 compliant), USB 2 cash drawers are supported. When disconnecting the cable, always hold the connector. Orient the cash drawer cable connector correctly, insert it into the cash drawer interface connector on the back of the printer. Connect the drawer`s ground line to the printer`s ground terminal with a screw. [. . . ] With the FEED button pressed and held, turn the printer power on, and then press the FEED button twice. Are printed, the printer is now in the memory switch setting mode. (No indication for 0/1 with memory switch ranging from 7 to 10) Selecting memory switch When the FEED button is pressed short (within 2 seconds), printing occurs in the order of "Memory SW1" "Memory SW2" "Memory SW3" . When the memory switch you want to change is reached, press and hold the FEED button (for more than 2 seconds). [. . . ]