User manual CITIZEN IDP-3210

[. . . ] LINE THERMAL PRINTER MODEL iDP3210 iDP3210 User's Manual Declaration of Conformity Manufacturer's Name : Manufacturer's Address Declare the Product Product Name Model Number(s) : Japan CBM Corporation : CBM Bldg. , 5-68-10, Nakano, Nakano-ku, Tokyo 164-0001, Japan Thermal Printer iDP3210 Series (iDP3210R, iDP3210P) (S. No. 0090001 ~ ) Conform to the following Standards LVD EMC : EN60950 : EN55022 : EN61000-3-2 : EN61000-3-3 : EN55024 : EN61000-4-2 : EN61000-4-3 : EN61000-4-4 : EN61000-4-5 : EN61000-4-6 : EN61000-4-8 : EN61000-4-11 : A4:1997 : 1998 Class A : 1995+A1:1998+A2:1998 : 1995 : 1998 : 1995 ±4KV CD, ±8KV AD : 1996 3V/m, 80MH-1000MHz AM 1KHz 80% : 1995 ±1. 0KV (AC Mains), ±0. 5KV (Signal Lines) : 1995 ±1KV (Normal mode), ±2KV (Cmmon mode) : 1996 3V, 0. 15MHz-80MHz AM 1KHz 80% : 1993 50Hz, 1A/m : 1994 0%, 5000ms/ 70%, 500ms/ 0%, 10ms Supplementary Information "The product complies with the requirements of the Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336EEC, 92/31/EEC, 93/68EEC" Place Date Tokyo, Japan September, 2000 Full Name: Mikio Moriya Position: General Manager R & D Department Europe Contact : Signature Norco Declaration AB Box 7146 S-250 07 Helsingborg Sweden Warning : This is a Class A products. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. This declaration is applied only for 230V model. CITIZEN iDP3210 User's Manual IMPORTANT SAFETY INSTRUCTIONS · · · · · · Read all of these instructions and save them for future reference. Follow all warnings and instructions marked on the product. [. . . ] ------------------ Factory Setting OFF OFF OFF OFF OFF ON ON OFF (Note) DS2 is available only for serial interface. Print Density DS1-9 DS1-10 Light OFF OFF Standard ON OFF Dark OFF ON Darker ON ON International Character DS1-6 DS1-7 DS1-8 BAUD RATE DS2-5 DS2-6 DS2-7 U. S. A. OFF OFF OFF 150 OFF OFF OFF France ON OFF OFF 300 ON OFF OFF Germany OFF ON OFF 600 OFF ON OFF U. K. ON ON OFF 1200 ON ON OFF Denmark I OFF OFF ON 2400 OFF OFF ON Sweden ON OFF ON 4800 ON OFF ON Italy OFF ON ON 9600 OFF ON ON Japan ON ON ON 19200 ON ON ON 20 CITIZEN iDP3210 User's Manual 6. 6. 1 INTERFACE (Connecting with Peripheral Equipment) Parallel Interface 8 bit parallel signal (DATA 1 ~ 8) ACK , BUSY , STB , FAULT , PE , RESET Printer side 57LE-40360 (Equivalent to amphenol ) 6. 1. 1 Specifications Data input method : Control signals: Applicable connector : 6. 1. 2 Connectoe's Pin Configuration No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Signal Name STB DATA 1 DATA 2 DATA 3 DATA 4 DATA 5 DATA 6 DATA 7 DATA 8 ACK BUSY PE +5V DC No. 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Signal Name TWISTED PAIR GND GND FRAME GND RESET FAULT GND Drawer switch output +5V DC 21 Cable side 57-30360 ( ) CITIZEN iDP3210 User's Manual 6. 1. 3 I/O SIGNALS (1) Input Signals to the Printer · DATA : 8-bit parallel signal (positive logic) · STB : Strobe signal to read 8-bit data (negative logic) · RESET : Signal to reset the entire printer (negative logic) 1m sec or more (2) Output Signals from Printer · ACK : An 8 bit data request signal. Pulse signal output at the end of the BUSY signal . (negative logic) · BUSY : The signal to indicate BUSY state of the printer. (positive logic) · FAULT : The signal which is made "LOW" when the printer is in alarm state. All the control circuits inside the printer are stop ped at this time. (negative logic) · PE : The signal which is output when paper runs out or goes scarce. (positive logic) · Drawer Switch Output : With the switch open, this signal goes "HIGH". When shorting, this goes "LOW". (3) Power supply · +5 V DC · GND : This is 5V pulled up by a 3. 3k resistor. : This is the common ground for the circuit. 22 CITIZEN iDP3210 User's Manual 6. 1. 4 Electrical Characteristics (1) Input Signal Level All the input signals are at C-MOS level. "HIGH" level "LOW" level (2) Output Signal Level All the output signals are at C-MOS level. "HIGH" level : 4. 5V MIN : 4. 0V MIN : 1. 0V MAX "LOW" level : 0. 1V MAX (3) I/O Conditions Both input signal of STB and RESET are pulled up by 3. 3K, and all of the other is pulled up by 50K. [Printer side] [Host side] All the output signals are pulled up by 50K. 23 CITIZEN iDP3210 User's Manual 6. 1. 5 TIMING CHART (1) Data Input and Printing Timing T4 T5 T6 : 270 ns MAX : 2. 3 s TYP : 500 ms MIN (On supplying power) 6. 1. 6 Data Receiving Control When BUSY signal is "LOW", data from the host can be received. received. 6. 1. 7 Buffering As the buffer of 4K byte can be buffered in input buffer, the host side can be released immediately. T1, T2, T3 : 0. 5 s MIN When it being "HIGH", data can not be 24 CITIZEN iDP3210 User's Manual 6. 2 Serial Interface 6. 2. 1 Specifications (1) Data transfer system : Asynchronous (2) Baud rates 150, 300, 600, 1200, 2400, 4800, 9600, 19200 bps (Selectable by user) (3) Configuration of one word Start bit Data bit Parity bit Stop bit : : : : 1 bit 7 bits or 8 bits (Selectable by user)) Add/even or no parity 1 bit or more (Selectable by user) (4) Signal polarity RS-232C · Mark · Space (5) Receive data (RD signal) RS-232C · Mark · Space = = 1 0 = = Logic " 1" (­3V to ­12V) Logic " 0" (+3V to +12V) (6) Data receiving control (DTR signal) RS-232C · Mark · Space : : Data transfer not available Data transfer available (7) Data transmission control (TD signal) DC1 code (11H) X-ON : DC3 code (13H) X-OFF : Data reception available Data reception not available 25 CITIZEN iDP3210 User's Manual 6. 2. 2 Connector's Pin Configurations No. 1 7 3 20 2 6 Signal Name FG GND RD DTR TD DSR I/O Function Frame Grand Signal GND Receiving data Printer BUSY signal Transmission data Data set READY Input Output Output Input Applicable connector (D-Sub connectors) Printer side Cable side : : 17LE-13250 (Equivalent to DDK) 17JE-23250 (Equivalent to DDK ) CAUTION 1. Signal for RS-232C conforms to EIA RS-232C. 2. In case the receiving data is not being transmitted, keep receiving data in mark state. 26 CITIZEN iDP3210 User's Manual 6. 2. 3 I/O SIGNALS (1) RD Serial receiving data signal. (2) DTR When this signal is READY, write data or a command. [. . . ] A portion exceeding 2048 bytes is not defined. · Even with ESC @ (initialization of the printer) having been executed, defined content is not cleared. Therefore, it is possible to include ESC @ into the content of macro definition. · Normal printing operation is carried out even while in macro definition. 51 CITIZEN iDP3210 User's Manual (37) Macro Execution (GS^ n1 n2 n3) Code : [1D]h + [5E]h + n1 + n2 + n3 * {0 n1 FF} {0 n2 FF} {0 3 1} Data is described in Hex code. Executing contents defined in macro. [. . . ]