User manual CITIZEN IDP-3423

[. . . ] DOT MATRIX PRINTER MODEL iDP3420 iDP3421 iDP3423 User's Manual iDP3420/3421/3423 User's Manual Declaration of Conformity This printer conforms to the following Standards: Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/31/EEC, 93/68/EEC. LVD : EN60950 EMC : EN55022 Class A EN61000-3-2 EN61000-3-3 EN55024 This declaration is applied only for 230V model. CITIZEN is a registered trade mark of CITIZEN WATCH CO. , LTD. , Japan CITIZEN es una marca registrada de CITIZEN WATCH CO. , LTD. , Japón ESC/POS and EPSON are a trademark and registered trademark of SEIKO EPSON CORPORATION Star is a registered trademark of Star Micronics Corporation Windows is a registered trademark of Microsoft Corporation CITIZEN iDP3420/3421/3423 User's Manual IMPORTANT SAFETY INSTRUCTIONS · · · · · · Read all of these instructions and save them for future reference. Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning. Do not place this product on an unstable cart, stand or table. [. . . ] 2 pin under the condition set with the <ESC><BEL> n1 n2 command. SUB [Function] Driving command for drawer-2 [Code] <1A>H [Outline] As soon as this command is received, the drawer connector no. power-on time is 200 ms ON and 200 ms OFF stationary. driven simultaneously. The The drawers 1 and 2 cannot be RS [Function] Buzzer-on [Code] <1E>H [Outline] This command emits a short warning sound from the printer. 51 CITIZEN iDP3420/3421/3423 User's Manual ESC "P" 0 [Function] Full cut (iDP3421/3423 only) [Code] <1B>H<50>H<00>H [Outline] This command fully cuts the paper. ESC "P" 1 [Function] Partial cut (iDP3421/3423 only) [Code] <1B>H<50>H<01>H [Outline] This command partially cuts the paper. ESC "R" n [Function] Selecting the international character set [Code] <1B>H <52>H n 0 n 10 This command selects the international characters according to the value of n. Denmark I Sweden n 6 7 8 9 10 Character Set Italy Spain Japan Norway Denmark II [Range] [Outline] [Default] Depends upon DIP switch setting. 52 CITIZEN iDP3420/3421/3423 User's Manual ESC "&" <0> n1 n2 [m0 m1 . . . m5 m6 m7 m8 m9] n2 - n1 + 1 [Function] Defining the Download character set [Code] <1B>H <26>H <00>H n1 n2 [m0 m1 . . . m5 m6 m7 m8 m9] n2 - n1 + 1 32 n1 n2 255 [Range] [Outline] m0 = 0 or m0 = 128 n1 is a character code to start definition This command defines he download characters. and n2 is to end definition, respectively. When defining only one character, set n1 = n2. Once the download characters are You can define the ASCII codes ranging from 32 to 255. defined, they remain valid until they are redefined or the download deletion command (ESC DC2 n1 n2) is executed. 53 CITIZEN iDP3420/3421/3423 User's Manual ESC "%" n [Function] Specifying/Canceling the download character set [Code] <IB>H <25>H n [Outline] This command selects/deselects the download character set. The download characters cannot be printed by simply defining them with the above-mentioned ESC & 0 command. To print them, send this command to the printer. n 0 30 1 31 Download Character Set Deselects Selects ESC "/" n "data" CR or LF [Function] Defining the Message [Code] <1B>H <2F>H n "data" CR or LF 1 n 10 This command can define up to a 50-byte message in one line. If the value of n is specified [Range] [Outline] beyond the range, the data following n will be treated as the print data. Once the message is defined, it remains valid until it is redefined. Once the message is defined, it remains valid until it is redefined or the download deletion command (ESC DC2 n1 n2) is executed. The data should end with If the data exceeds 50 bytes, the subsequent data will be treated as 54 CITIZEN iDP3420/3421/3423 User's Manual ESC DC3 n [Function] Printing the message [Code] <1B>H <13>H n 1 n 10 This command prints a message. If the value of n is specified beyond the range, the [Range] [Function] ESC "y" n [Function] Setting the print lines after paper near end detection [Code] <1B>H<79>H n 0 n1 255 This command sets the number of print lines after paper near end detection. It stops [Range] [Outline] printing after printing n × 2 lines since detection of the paper near end, resulting in the paper near end state (See 4. 12 Operation Panel and Error Indications). (Serial/Parallel) changes when the paper near end is detected. The PE signal [Default] n=0 55 CITIZEN iDP3420/3421/3423 User's Manual ESC DC2 n1 n2 [Function] Deleting the download character, message, bit image [Code] <1B>H <12>H n1 n2 0 n1 3 0 n2 (Specify 0 at n1 = 0) (1 n2 10 at n1 = 1) (32 n2 255 at n1 = 2) (Specify 0 at n1 = 3) [Range] [Outline] This command deletes the downloaded characters, message, and bit image. n1 0 1 2 3 Object Deleted All(Message, characters, bit image) Download message Download characters Download bit image With n2, specify which data of the function specified with n1 should be deleted. n2 = 0 n20 Deletes all the data saved with the download function specified with n1. Deletes the data downloaded at the value specified with n2 (Value specified when saving with each download command), of the d ownload function specified with n1. Note) No meaning when n1 = 0 is set. 56 CITIZEN iDP3420/3421/3423 User's Manual GS "" n1 n2 [d] n1 × n2 × 8 [Function] Defining the download, bit image <1D>H <2A>H <n1> <n2> [<d>] n1 × n2 × 8 1 n1 45 0 n2 24 [Code] [Range] Note) Take care that the number of data (n1×n2×8) is equal to or smaller than 2, 048. [. . . ] Fehleranzeige ERROR-Lämpchen Signalgeber Mechanischer Fehler Rasches Blinken Etwa 1 Sekunde anhaltender Signalton Papierende Leuchtet Drei kurze Signaltöne, in Abstand von 0, 6 Sekunden wiederholt werden Papierrolle fast leer Blinkt (in Drei kurze Signaltöne, in Sekundenabständen) Abstand von 0, 6 Sekunden wiederholt werden Motorsperre des Rasches Blinken Etwa 1 Sekunde langer Schneidemechanismus (zweimal pro Sekunde) Signalton (nur iDP3421/23) Mechanischer Fehler Rückstellmethode Den Netzschalter rückstellen. Den Papierstau beseitigen. : Wenn der Druckmechanismus aufgrund eines Papierstaus o. höher als normal belastet wird, erklint ein Signalton, und das ERROR-Lämpchen blinkt, um den Druckmechanismus zu stoppen. Papierende : Bei aufgebrauchte-m Papiervorrat erkennt der Sensor im Papierweg in der Nähe des Druckkopfes das Ende der Papierrolle, schaltet den Signalgeber und das ERROR-Lämpchen ein, um den Druckmechanismus zu stoppen. Durch Einschieben des Papiers in den Papierweg wird die Papierrolle geladen (siehe 4. 7 "Einlegen des Papiers"). Papiervorrat fast leer : Bei aufgebrauchtem Papiervorrat wird der Papierrestsensor zum Einschalten des Signalgebers und des ERROR-Lämpchens aktiviert. [. . . ]