User manual CITIZEN IDP-3541

[. . . ] DOT MATRIX PRINTER MODEL iDP3540/3541 iDP3540/3541 User's Manual Declaration of Conformity Manufacturer's Name : Manufacturer's Address : Japan CBM Corporation : CBM Bldg. , 5-68-10, Nakano, Nakano-ku, Tokyo, 164-0001, Japan Declare the Product Product Name Model Number(s) Dot Matrix Printer iDP3540, 3541 Series (iDP3540R, iDP3540P, iDP3541R, iDP3541P) (S. No. 0090001 ~ ) Conform to the following Standards LVD EMC : EN60950 : EN55022 : EN61000-3-2 : EN61000-3-3 : EN55024 : EN61000-4-2 : EN61000-4-3 : EN61000-4-4 : EN61000-4-5 : EN61000-4-6 : EN61000-4-8 : EN61000-4-11 : A4:1997 : 1998 Class B : 1995+A1:1998+A2:1998 : 1995 : 1998 : 1995 ±4KV CD, ±8KV AD : 1996 4. 5V/m, 80MHz-1000MHz AM 1KHz 80% : 1995 ±1. 0KV(AC Mains), ±0. 5KV(Signal Lines) : 1995 ±1KV (Normal mode), ±2KV (Common mode) : 1996 3V, 0. 15MHz-80MHz AM 1KHz 80% : 1993 50Hz, 3A/m : 1994 0%, 5000ms/ 70%, 500ms/ 0%, 10ms Supplementary Information "The product complies with the requirements of the Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336EEC, 92/31/EEC, 93/68EEC" Place Date Tokyo, Japan September, 2000 Full Name Position Europe Contact : : Mikio Moriya : General Manager R & D Department Signature Norco Declaration AB Box 7146 S-250 07 Helsingborg Sweden This declaration is applied only for 230V model. CITIZEN iDP3540/3541 User's Manual IMPORTANT SAFETY INSTRUCTIONS * Read all of these instructions and save them for later reference. * Follow all warnings and instructions marked on the product. * Unplug this product from the wall outlet before cleaning. [. . . ] 2) Confirm that the ribbon cassette is properly installed and turn the power switch off. 3) Turn the power switch ON while pressing the LF switch, and release the LF switch after the self test operation has begun. In the above operation, the self print function will stop automatically when completed. However, the self print function will not operate without paper. Alarm and Paper Near-End Detection This printer has the paper near-end sensor to stop the operation when the paper comes to near-end, sending out both BUSY and FAULT signals. This status is indicated by the SEL / ALARM lamp blinking at an interval of 1. 0 second. 7. Input Buffer Back-up Function 7. 1 Input Buffer Back-up If the power is turned off, or there is a power failure during printing, the data in the input buffer will be retained. When the power comes back on, the power failure symbol (. . . . . PD) will be printed, and then the data which was interrupted will be printed from the beginning of the line where the interruption occurred. Note: The input buffer back-up function may not operate properly if the related capacitor is not sufficiently charged. This may be the case if the printer has not been operated for a long period of time. After the printer power switch has been turned on for 10 minutes, the buffer back-up should be effective for approximately 24 hours or more. 7. 2 Clearing the Input Buffer In case it is desired to delete the data in the input buffer, the power switch should be turned on while pressing the SEL switch. When deletion of the buffer is completed the buzzer will sound. Please be sure to continue pressing the SEL switch until that time. If the printer fails to work properly at the time the power switch is turned on, please delete the input buffer as described above before inputting new data. CITIZEN 13 iDP3540/3541 User's Manual 8. Parallel Interface 8. 1 Specifications a) Data Input system : b) Control Signals : c) Compatible Connector : 8 bit parallel (DATA 1~8) ACK, BUSY, STB, FAULT, PE, RESET Printer side : 57LE-40360 (AMPHENOL or equivalent) Cable side : 57-30360 (AMPHENOL or equivalent) 8. 2 Connector Pin Assignment Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Signal Name STB DATA 1 DATA 2 DATA 3 DATA 4 DATA 5 DATA 6 DATA 7 DATA 8 ACK BUSY PE "H" Level GND GND GND FRAME GND Pin No. 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Signal Name Twisted Pair GND RESET FAULT CITIZEN 14 iDP3540/3541 User's Manual 8. 3 Description of Input / Output Signals 8. 3. 1 Input / Output Signals a) Input / Output Signals * DATA : 8 bit parallel signal. (Positive logic) * STB : A strobe signal for reading in 8 bit data. (Negative logic) * RESET : A signal which resets the entire printer. (Negative logic, 1 ms or more) b) Output Signals (From Printer) This is a pulse signal for requesting 8 bit data, issued at the end of a BUSY signal. (Negative logic) * BUSY : This signal indicates that your printer is in a BUSY state. New data should be input when this signal is "LOW". [. . . ] (1) Printer head returns to its start position. (2) SELECT (ON-LINE) or DESELECT (OFF-LINE) status may be chosen by the Dip Switches for Pre-Setting. (6) The first line set at the present line. (7) Designation of Red printing is cleared. [. . . ]