User manual CITIZEN IDP-560RS

[. . . ] Unplug this product from the wall outlet before cleaning. Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage to the product. Slots and openings on the back or bottom of the case are provided for ventilation. [. . . ] Set new paper Paper end Illuminated Set new paper (Quick blinking) Cutter motor lock Illuminated Eliminate paper jam (Quick blinking & slow blinking) Macro execution wait Illuminated Press FEED switch. (slow blinking) Details of error Cover open : When printer cover is opened, printer cover open sensor detects the cover opening and has ERROR LED illuminate, then stops printing operation. But, depending on dip switch setting, paper feed can be performed when printer cover is opened. 17 CITIZEN iDP3210 User's Manual Print Head overheat : To protect print head from excessive heat, in case the temperature of print head goes high(approx. 65°C or over), head temperature sensor works and has ERROR LED illuminate, then stops printing operation. After head temperature is cooled (Approx. 60°C or less), printing operation automatically starts. Paper near end : When the remaining of roll paper goes scarce, paper near end sensor located on the side of roller portion of the upper cover works, and has ERROR LED illuminate to show the remaining of roll paper is getting scarce. (See "setting of paper end detector effective for outputting a signal for no paper" and "setting of paper end sensor effective for print stop" in the chapter of print control function. ) Paper end : When the roll paper runs out completely, the paper sensor located in the paper course near to print head detects the end of print paper and has ERROR LED illuminate, then stops printing operation. (See "setting of paper end sensor effective for outputting a signal for no paper" and "setting of paper end sensor effective for print stop" in the chapter of print control function. ) When the paper is inserted into the paper course near to print head, roll paper is automatically loaded. Cutter motor lock : In case that cutter position sensor locates in the auto cutter unit keeps ON or OFF for one second or more during the operation of cutter motor, this sensor detects it as motor lock state. And then, this stops cutter operation and printing operation. (See the chapter of 4. 5 "cancellation of cuter lock") (3) FEED Switch With this pressed once shortly, paper is fed by one line. With this kept pressed, lines are fed continuously. In case of macro execution wait, this is executed by pressing FEED switch. (4) FEED Switch and Power Switch By turning ON power switch with pressing FEED SWITCH, , self printing is performed. 18 CITIZEN iDP3210 User's Manual 5. 5. 1 Dip Switch Setting Location of Dip Switch (1) Turn OFF the power switch. (Remove it by taking off two screws at the botto m and turning the cover in the arrowed direction. ) 19 CITIZEN iDP3210 User's Manual 5. 2 Dip Switch Setting DS1 DS1-1 DS1-2 DS1-3 DS1-4 DS1-5 DS1-6 DS1-7 DS1-8 DS1-9 DS1-10 Function Paper cutter Cover open CR switching Unused Print columns International Characters International Characters International Characters Print density Print density ON Enabled Disabled LF activate 44 columns OFF Disabled Enabled Ignored 42 columns Factory Setting ON OFF OFF OFF ON OFF OFF OFF OFF ON See the table below. (2) DTR When this signal is READY, write data or a command. When they are written in BUSY, overrun error is On occurrence of framing error, overrun error, or parity error, the data is occurred and data is ignored. Even during printing, data can be loaded in the input buffer. Further, BUSY can take place on supply of power, during test printing, during on-line, or on resetting. (3) TD When, while in data reception, the input buffer on the printer side has only 128 bytes . or less left, DC3(13H) data reception impossible signals are output. When the input buffer has 256 bytes left, DC1 (11H) data reception possible signals are output to the host. When DTR/DSR control having been selected in status information transmission, it is first confirmed that DSR is "space" and data is sent. control has not been selected, DSR is ignored and data is transmitted. (4) FG Case GND (5) GND Common GND on the circuit. When DTR/DSR 27 CITIZEN iDP3210 User's Manual 6. 2. 4 Mark Data Configuration -------Æ t Space (1) (2) (3) (1) Start bit (2) Data bit (+ parity bit) (3) Stop bit ( 1 or more ) (1) Start Bit In 1/2 bit from the mark-to-space starting edge, state is read once again. When "space" state is confirmed, it is recognized as the start bit. [. . . ] · A portion of a download bit image exceeding one line length is not printed. · A download character and a download bit image cannot be defined simultaneously. (36) Starting / Ending Macro Definition (GS :) Code : [1D]h + [3A]h Specifying starting / ending macro definition. Maximum content available for macro definition is 2048 bytes. [. . . ]