User manual CITIZEN IDP3110 QUICK GUIDE

[. . . ] DOT MATRIX PRINTER MODEL iDP3110 iDP3110 User's Manual Declaration of Conformity Manufacturer's Name : Manufacturer's Address : Japan CBM Corporation : CBM Bldg. , 5-68-10, Nakano, Nakano-ku, Tokyo, 164-0001, Japan Declare the Product Product Name Model Number(s) Dot Matrix Printer iDP3110 Series (iDP3110R, iDP3110P) (S. No. 0090001 ~ ) Conform to the following Standards LVD EMC : EN60950 : EN55022 : EN61000-3-2 : EN61000-3-3 : EN55024 : EN61000-4-2 : EN61000-4-3 : EN61000-4-4 : EN61000-4-5 : EN61000-4-6 : EN61000-4-8 : EN61000-4-11 : A4:1997 : 1998 Class B : 1995+A1:1998+A2:1998 : 1995 : 1998 : 1995 ±4KV CD, ±8KV AD : 1996 4. 5V/m, 80MHz-1000MHz AM 1KHz 80% : 1995 ±1. 0KV(AC Mains), ±0. 5KV(Signal Lines) : 1995 ±1KV (Normal mode), ±2KV (Common mode) : 1996 3V, 0. 15MHz-80MHz AM 1KHz 80% : 1993 50Hz, 3A/m : 1994 0%, 5000ms/ 70%, 500ms/ 0%, 10ms Supplementary Information "The product complies with the requirements of the Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336EEC, 92/31/EEC, 93/68EEC" Place Date Tokyo, Japan September, 2000 Full Name Position Europe Contact : : Mikio Moriya : General Manager R & D Department Signature Norco Declaration AB Box 7146 S-250 07 Helsingborg Sweden This declaration is applied only for 230V model. CITIZEN iDP3110 User's Manual IMPORTANT SAFETY INSTRUCTIONS * Read all of these instructions and save them for later reference. * Follow all warnings and instructions marked on the product. * Unplug this product from the wall outlet before cleaning. [. . . ] Insert paper after moving aside the paper holder in the direction of the arrow. Then, secure the center of the roll with the holder. (6) Then, attach the printer cover so the end of the paper comes out of the opening in the cover. (1) (2) (3) (4) (5) CITIZEN 9 iDP3110 User's Manual 4. 5 Self Test Printing A self-printing function is incorporated in this product to enable the printer to check itself. This function is triggered by the following procedure. (2) Ensure that the ribbon cassette is attached correctly and turn the power OFF. (3) Turn ON the power switch while holding the LF switch down. Release the LF switch after the self-printing operation has started. Printing is initiated by this operation. To end self-printing, turn OFF the printer. 4. 6 General Notices (1) Never operate your printer without loading paper and ribbon cassette. Any printing without paper and ribbon cassette may cause damage to printer head. (2) Replace ribbon cassette before it is worn with rents. (3) Be careful not to drop any foreign matters, such as paper clips and pin and the like into your printer. (4) Nothing shall be placed on the radiation vents to the printer. (5) Place your printer always on a stable desk which is set horizontal. (6) No organic solvent (thinner, benzin or the lie) shall be used in sweeping clean the surface of the main body case. (7) Make sure that the power of the printer is turned off whenever you do the following. 1) Taking out any foreign matter which was dropped into the printer. 2) Replacing the ribbon cassette. CITIZEN 10 iDP3110 User's Manual 5. PARALLEL INTERFACE 5. 1 Specifications a) Data input system b) Control signal c) Compatible Connector : 8 bit parallel (DATA 1-8) : ACK, BUSY, STB, RESET, SELECT : Printer side : 57LE-40360 (AMPHENOL or equivalent) : Cable side : 57-30360 (AMPHENOL or equivalent) 5. 2 Connector Pin Assignment PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 SIGNAL NAME STB DATA 1 2 3 4 5 6 7 8 ACK BUSY GND SELECT GND GND FRAME GND PIN 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 SIGNAL NAME TWISTED PAIR GND GND RESET GND CITIZEN 11 iDP3110 User's Manual 5. 3 Description of Input / Output Signals (1) Input signal All input signals utilize type 74HC of CMOS and can be used in TTL level as the input is pulled up with 3. 3 k resistance. - DATA 8 bit parallel signal (positive logic) - STB Strobe signal for reading out data (negative logic) - RESET Signal for resetting the entire unit (negative logic 4ms or more) (2) Output signal TTL is utilized for all output signals. [. . . ] A1 signifies the starting address for the registration and A2 is the ending address. [Method of data transmission] d-1) Single character registration Select the address to be defined (character code) from among 20H to FFH and designate is as A1. When registering a single character, starting and ending addresses match each other. <Example> A 6 × 8 dot matrix full dot pattern is to be registered in address 41H (code for the fixed character "A"). [. . . ]