User manual CITIZEN IDP3240 QUICK GUIDE

[. . . ] Declaration of Conformity Manufacturer's Name : Japan CBM Corporation Manufacturer's Address : CBM Bldg. , 5-68-10, Nakano, Nakano-ku Tokyo, 164-0001, Japan Declare the Product Product Name Model Number(s) Line Thermal Printer iDP3240 Series (iDP3240RF/PF) (S. No. 9990001~) Conform to the following Standards LVD : EN60950 EMC : EN55022 : EN61000-3-2 : EN61000-3-3 : EN55024 : EN61000-4-2 : EN61000-4-3 : EN61000-4-4 : EN61000-4-5 : EN61000-4-6 : EN61000-4-8 : EN61000-4-11 : A11: 1997 : 1998 Class A : 1995 : 1995 : 1998 : 1995 ±4KV CD, ±8 KV AD : 1995 3 V/m, 80 MHz-1000 MHz AM 1 KHz 80 % : 1995 ±1. 0 KV(AC Mains), ±0. 5 KV(Signal Lines) : 1995 ±1 KV Normal mode, ±2 KV Common mode : 1996 3 V, 0. 15 MHz-80 MHz AM 1 KHz 80 % : 1993 50 Hz, 3 A/m(Out of scope) : 1994 10 ms/95 %, 500 ms/30 %, 5000 ms/100 % Supplementary Information "The product complies with the requirements of the Low Voltage Directive 73/ 23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/31/EEC, 93/68/EEC" Place Date Tokyo, Japan August, 1999 Full Name : Mikio Moriya Position : General Manager R & D Department European Contact : Norco Declaration AB Box 7146 S-250 07 Helsingborg Sweden Signature Warning : This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. This declaration is applied only for 230 V model. --i-- IMPORTANT SAFETY INSTRUCTIONS · Read all of these instructions and save them for future reference. · Follow all warnings and instructions marked on the product. [. . . ] Each bit for "n" has the following meaning: Bit 0 1 2 3 4 5 6 7 Position Paper Near-end Paper Near-end Paper end Paper end Undefined Undefined Undefined Undefined Value 0 1 Disabled Enabled Disabled Enabled Disabled Enabled Disabled Enabled [Caution] This command is valid only for the parallel interface. Bits 1 and 2, and bits 2 and 3 are valid if either bit is "1". If all bits are set to be invalid, the paper end signal always indicates that paper is available. [Default] n = 15 -- 88 -- ESC c 4 n [Function] [Code] [Range] [Outline] Selecting the Paper Near-end Sensor valid for print stop <1B>H<63>H<34>H<n> 0 n 255 This command selects the Paper Near-end Sensor which helps to stop printing when the paper supply almost runs out. Each bit for "n" has the following meaning: Bit 0 1 2 3 4 5 6 7 Position Paper Near-end Paper Near-end Undefined Undefined Undefined Undefined Undefined Undefined Value 0 1 Disabled Enabled Disabled Enabled This printer can only select one kind of Paper Sensor, a Paper Near-end Sensor. [Default] n=0 -- 89 -- ESC c 5 n [Function] [Code] [Range] [Outline] Enabling/Disabling the panel switches <1B>H<63>H<35>H<n> 0 n 255 Enabling/disabling the FEED switch. · "n" is valid only in the lowest bit. n0 0 1 Condition FEED switch valid FEED switch invalid [Caution] When the panel switch is disabled with this command, the FEED switch is also disabled. Therefore, the paper cannot be fed by operating the FEED switch. Regardless of the setting of this command, the FEED switch is always enable while the switch is being waited for at the time of macro execution. n=0 LPRINT CHR$(&H1B) + "c5" + CHR$(0); When enabling the FEED switch LPRINT CHR$(&H1B) + "c5" + CHR$(1); When disabling the FEED switch [Default] [Sample Program] -- 90 -- ESC d n [Function] [Code] [Range] [Outline] Printing and feeding the paper by "n" lines <1B>H<64>H<n> 0 n 255 Prints data in the print buffer and feeds paper by "n" lines. · The beginning of the line is specified as the next print start position. [Caution] [Default] [Sample Program] If [n × line feed width] exceeds approximately 1016 mm, this command feeds paper by approximately 1016 mm (40 inches). LPRINT "AAAAA"; LPRINT CHR$(&H1B) + "d" + CHR$(2); LPRINT "AAAAA" + CHR$(&HA); END AAAAA [Print Results] AAAAA 2/6-inch line feed -- 91 -- ESC p m n1 n2 [Function] [Code] [Range] Generating the specified pulses <1B>H<70>H<m><n1><n2> m = 0, 1, 48, 49 0 0 [Outline] n1 n2 255 255 The signals specified by "n1" and "n2" are output to the connector pin specified by "m". · "m" has the followings. m 0, 48 1, 49 Connector Pin Drawer Kick-Out pin No. 2 Drawer Kick-Out pin No. 5 · The ON time is n1 × 2 ms, and OFF time n2 × 2 ms. [Caution] · When "m" is beyond a definition range, no signal is output, discarding "n1" and "n2". · The drawer drive duty must be within the following range: ON time ON time + OFF time (The OFF time should be 4 times or more longer than the ON time. ) [Default] [Sample Program] LPRINT CHR$(&H1B) + "p"; LPRINT CHR$(0); Selects pin No. LPRINT CHR$(5); Sets ON time to 10ms LPRINT CHR$(50); Sets OFF time to 100ms END The initial value for "m", "n1" and "n2" is not defined. 0. 2 -- 92 -- ESC t n [Function] [Code] [Range] [Outline] Selecting the character code table <1B>H<74>H<n> 0 n 9, n = 255 Selecting the character code table: The character code table is selected based on the value of "n". n 0 1 2 3 4 5 6 7 8 9 255 Character Code Table Codepage PC437 (USA, European Standard) Codepage Katakana (Japanese) Codepage PC850 (Multilingual) Codepage PC860 (Portuguese) Codepage PC863 (Canadian-French) Codepage PC865 (Nordic) Codepage PC852 (Eastern Europe) Codepage PC866 (Russian) Codepage PC857 (Turkish) Windows Codepage Space Page (For user setting) [Default] [See Also] [Sample Program] This is a character code table specified with DIP Switch. CHARACTER CODES TABLE" LPRINT CHR$(&H1B) + "t" + CHR$(0); LPRINT "n"=0; FOR C=&HB2 TO &HB5 LPRINT CHR$(C); NEXT C LPRINT CHR$(&HA); LPRINT CHR$(&H1B) + "t" + CHR$(9); LPRINT "n"=9; FOR C=&HB2 TO &HB5 LPRINT CHR$(C); NEXT C LPRINT CHR$(&HA); END n=0 n = 0 [Print Results] n= 9 23'µ -- 93 -- n = 9 ESC { n [Function] [Code] [Range] [Outline] Specifying/Canceling the inverted characters <1B>H<7B>H<n> 0 n 255 Specifying/canceling inverted characters. · "n" is valid only for the lowest bit. n0 0 1 Condition Canceling inverted characters. Specifying inverted characters. [Caution] · Inverted printing means printing the line turned 180°. · This command is valid only when it is specified at the beginning of a line. · The settings of this command have no effect on PAGE MODE, but items set in PAGE MODE are valid even after STANDARD MODE resumes. [Default] [Sample Program] n=0 LPRINT CHR$(&H1B) + "{" + CHR$(0); LPRINT "AAAAA" + CHR$(&HA); LPRINT "BBBBB" + CHR$(&HA); LPRINT CHR$(&H1B) + "{" + CHR$(1); LPRINT "AAAAA" + CHR$(&HA); LPRINT "BBBBB" + CHR$(&HA); END [Print Results] AAAAA BBBBB Inversion Specified Inversion Canceled Paper Feed Direction -- 94 -- AAAAA BBBBB GS ! [. . . ] Wenn die Pulsbreite des Signals im Leerzeichenzustand 1 ms oder länger beträgt, wird ein Rücksetzungssignal übertragen. (6) FG Hierbei handelt es sich um ein Massesignal. -- 205 -- (7) GND Hierbei handelt es sich um die gemeinsame Erde von Schaltkreisen. 7. 3. 2 Fehlererkennung Dieser Drucker kann Paritätsfehler, DÜ-Blockfehler und Überlauffehler erkennen. Wenn ein Fehler erkannt wird, werden die fehlerhaften Daten im Pufferspeicher als "?" gespeichert. (1) DÜ-Blockfehler Wenn ein Leerzeichenzustand zum Zeitpunkt einer Stoppbiterkennung erkannt wird, ist ein Fehler aufgetreten. [. . . ]