User manual CITIZEN L310III

[. . . ] 5 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 SAFETY INSTRUCTIONS which must be strictry observed!. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 2 Paper cut bar It is used to cut the paper manually. 3 Platen open lever It is a lever used to open the platen unit on the rewinder equipped model. Open the platen unit by pulling it towards you. 4 Print head cover 6 5 Ribbon cassette drive shaft 6 Print head Auto cutter and rewinder equipped model 8 1 2 3 4 5 7 7 Rewinder shaft It rewinds the copy side of the copy roll paper. 8 Auto cutter unit It automatically cuts the paper after printing is completed. The cut action is set by a command in Soft SW Setting Mode. Names and Functions of Parts 6 17 Chapter2 Names and Functions of Parts Operation Panel 1 2 3 4 1 POWER LED (Green) It is lit when the power is supplied. When maintenance mode is set or there is an error indication, it is either lit or flashing. 2 PAPER OUT LED (Orange) It is lit in paper out status. When maintenance mode is set or there is an error indication, it is either lit or flashing. 3 ERROR LED (Orange) It is lit when the rear cover or front cover is open. When maintenance mode is set or there is an error indication, it is either lit or flashing. 4 FEED Switch When this switch is pressed once, paper feeds (1 line). The cover of the power cord will melt, causing fire or electric shock. When the printer will not be used for a long period, be sure to remove the plug of the power cord from the outlet to guarantee safety. Isolate the AC power source from other devices that generate noise. Flat side of the cable is up. AC adapter type AC inlet Built-in AC adapter type 22 Installation This printer can be installed horizontally or vertically and can be wall mounted. But according to the model you are using, there may be restrictions on how it is installed. Horizontal Standard model (AC adapter type) Standard model (Built-in AC adapter type) Auto cutter equipped model (AC adapter type) Auto cutter equipped model (Built-in AC adapter type) Auto cutter and rewinder equipped model (AC adapter type) Auto cutter and rewinder equipped model (Built-in AC adapter type) Yes Yes Yes Yes Yes Yes Vertical No Yes*1 No Yes*1 No No Wall Mount Yes*2 Yes*2 Yes*2 Yes*2 No No *1: Accessory rubber feet must be used to prevent slipping. *2: The optional specialized wall hanging unit is necessary to hang it on the wall. Preparing the Printer Horizontal Vertical and wall mounted 23 Chapter3 Preparing the Printer Setting the Paper Near End Sensor Change the sensor location according to the way the printer is installed and the interior diameter of the roll paper you are using. Referring to the following table, set it at a location suited to the usage environment by moving it to the left and right while pushing the concave part of the center of the sensor with your finger. (When shipped from the factory, it is set at 24mm. ) Paper near end sensor When installed vertically and wall hung 6 5 4 32 1 When installed horizontally Installation method Horizontal Remaining roll paper (mm) Approx. 22 Sensor location 1 2 3 4 5 6 Vertical (wall hung) Caution The remaining roll paper (external diameter of the roll paper) differs greatly according to the type of roll paper used. When the sensor has detected the remaining roll paper during printing, the printer stops printing after it has printed all the data that it had received. If you are using a model with parallel (IEEE1284) interface specifications, you can select sensor enabled/disabled in Soft SW Setting Mode. [. . . ] If you do, the printer will be damaged and you will be cut by the blade. Maintenance Mode 3 Ribbon does not feed correctly Turn the knob on the ribbon cassette. After turning the knob until the ribbon feeds smoothly, reset the ribbon cassette. If you cannot turn the knob, the ribbon may be jammed inside the cassette. If the situation does not improve, replace it with a new ribbon cassette. 4 The paper is not cut Check to make sure that the rear cover and front cover are closed. If one of the covers is open, close it. If the paper still cannot be cut after you have closed the cover, notify the dealer where you purchased the printer or service personnel. 43 Chapter5 Appendixes Specifications Printing mode Printing direction Head pins Printing line number Serial impact dot matrix Bi-directional 9 pins (: 0. 3mm, Pin interval; 1/72inch) Paper width of 76. 2mm 40/42 or 33/35 lines Paper width of 69. 5mm 36/30 or 38/31 lines Paper width of 57. 5mm 30/25 or 31/26 lines 200/400 dots (full dot/including half dot) 79 or 99 dots ASCII (96 characters), International characters, Katakana Code pages 437, 850, 860, 863, 865, 852, 866, 857, 858, WPC1252 1 switch (FEED), 3 LED (POWER/PAPER OUT/ERROR), 1 buzzer Printing: 240CPS (3P paper 200CPS) Through-put: 76. 2mm wide, 40 columns (79+3sp, 6LPI) 5. 0LPS 69. 5mm wide, 36 columns (79+3sp, 6LPI) 5. 4LPS 57. 5mm wide, 30 columns (79+3sp, 6LPI) 6. 0LPS Friction feed Minimum pitch: 1/144 inch Paper feed speed: 40LPS (6LPI) 1P roll paper 2P copy roll paper (1 original + 1 copy) 3P copy roll paper (1 original + 2 copies) * When 3P, printing speed falls 16% Paper widths: 76. 2 / 69. 5 / 57. 5 (±0. 5)mm Roll diameter: 30mm to 83mm Core diameter: Interior diameter 10 +2 mm, exterior diameter 27mm or less ­0 Paper thickness: 1P 0. 06 to 0. 085mm Copy paper 0. 05 to 0. 20mm (total thickness) But the total thickness that can be cut is from 0. 05 to 0. 14mm. [. . . ]