User manual CITIZEN LC110III

[. . . ] If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. [. . . ] G Before connecting or disconnecting AC adapter, turn the printer power OFF. Do the operation securely. --8-- THE TABLE OF CONTENTS 1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 1. 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 1. 2 Included and Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1. 3 Type Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GENERAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EXPLANATION OF PRINTER PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 3. 1 3. 2 3. 3 3. 4 3. 5 3. 6 4. 1 4. 2 4. 3 4. 4 4. 5 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Communication Port and Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inside of Paper Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 8. 1 How to Mount Belt Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 8. 2 Mounting Rubber Feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INTRODUCTION LC110III is a compact, full featured portable line thermal printer, which can be used in a large variety of job environments ranging from door-todoor sales through small and mid-sized catering establishments, carrentals, parking lots, field services to on-board sales on land, sea and air. IrDA communication with a PDA or similar device is useful for business activities at the point of sale or service. 80 cm Emulation Characters Characters per line Dot matrix Bar code type Paper feed system Paper width Paper thickness Recommended paper Paper roll maximum diameter Minimum core diameter Interfaces IrDA Interface -- 12 -- Feature Serial interface Parameters Speed: 1200, 2400, 4800, 9600, 19200, 57600, 115200 bps Interface: Bidirectional serial communication Signal level: RS-232C Data lenght: 8 bits Start bit: 1 bit Stop bit: 1 bit Parity: None Flow control: Xon/Xoff Connector: Motorola Star Tac 64 KB Track 1, 2, 3 Power LED: GREEN and RED Charge LED: GREEN and RED Power switch 1, LF switch 1 Paper end sensor, Open cover sensor, Head temperature, Low battery Idle - approximately 2W When printing - approximately 15W Battery type: Li-ion battery pack Cell Voltage: 3. 7 V Number of cells: 2 Battery pack voltage: 7. 4 V Battery pack capacity: 2000 mAh Approximately 3 hours by main unit + AC adapter 40, 000 lines (At temperature 20°C, standard setting, alphanumeric slide pattern printing. The number of lines may be changed by such condition as temperature, etc. ) Auto Power OFF (programmable - from 1 to 60 min. ) Low battery monitoring included. Model: 10AD-JU (for Japan, USA, and Canada) 10AD-E (Europe) Input voltage 90 V - 264 V AC Output voltage 9. 0 V DC 1. 0 A Temperature: 5 ­ 40°C Humidity: 35 ­ 80% RH (No dew condensation) Temperature: ­20 ­ 60°C Humidity: 10 ­ 90% RH (No dew condensation) Input buffer Mag stripe reader LED color Operation switches Sensors and error monitoring Power consumption Battery Battery charging time Maximum lines printed with fully charged battery Power supply monitoring AC Adapter Operating Environment Storage Environment -- 13 -- Feature Reliability Parameters Print head: 100, 000, 000 pulses or 50km (Normal temperature, 12. 5% density, rated energy) Mechanism: 15, 000, 000 lines UL, C-UL, TUV, GS, CE Marking FCC Class B, VCCI Class B 116 (W) × 104 (D) × 63 (H) mm (50 mm paper cover + Mag stripe reader) Approx. 370 g (with battery and belt clip without paper) Serial Cable, Mag Stripe card reader (Factory option) Safety standard and EMI Dimensions Weight Options -- 14 -- 3. EXPLANATION OF PRINTER PARTS (3) (1) (5) (8) (9) (4) (7) (2) (6) 3. 1 LED Indicators (1) Charge LED RED on: Battery is charging GREEN on: Battery is Fully charged (2) Power (Error) LED GREEN on: Lights when printer is powered ON. RED/GREEN blinks fast: No paper or cover open. RED/GREEN blinks slow: Print head is overheated or macro is in process and awaiting LF switch operation. [. . . ] Remove battery pack from compartment and disconnect battery connector from main unit. -- 25 -- 4. 7 Installing the Battery Pack 1. Insert the battery connector to the connector of the printer. Insert the battery connecting cable into the opening above the battery connector. Confirm that the battery connector is seated deeply. [. . . ]