User manual CITIZEN LC310

[. . . ] ·Unplug this product from the wall outlet before cleaning. ·Do not use this product near water. ·Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage to the product. [. . . ] n 0 1 2 3 4 5 [Default] Character Set U. S. A. Denmark I Sweden n 6 7 8 9 10 Character Set Italy Spain Japan Norway Denmark II Depends upon DIP switch setting. - 51 - ESC "&" <0> n1 n2 [m0 m1 . . . m5 m6 m7 m8 m9] n2 - n1 + 1 [Function] [Code] [Range] [Outline] Defining the Download character set <1B>H <26>H <00>H n1 n2 [m0 m1 . . . m5 m6 m7 m8 m9] n2 - n1 + 1 32 £ n1 £ n2 £ 255 m0 = 0 or m0 = 128 n1 is a character code to start When defining only one This command defines he download characters. character, set n1 = n2. definition and n2 is to end definition, respectively. You can define the ASCII codes ranging from 32 to 255. Once the download characters are defined, they remain valid until they are redefined or the download deletion command (ESC DC2 n1 n2) is executed. - 52 - ESC "%" n [Function] [Code] [Outline] Specifying/Canceling the download character set <IB>H <25>H n This command selects/deselects the download character set. The download characters cannot be printed by simply defining them with the above-mentioned ESC & 0 command. To print them, send this command to the printer. n 0 30 1 31 Download Character Set Deselects Selects ESC "¤" n "data" CR or LF [Function] [Code] [Range] [Outline] Defining the Message <1B>H <2F>H n "data" CR or LF 1 £ n £ 10 This command can define up to a 50-byte message in one line. If the value of n is specified beyond the range, the data following n will be treated as the print data. Once the message is defined, it remains valid until it is redefined. subsequent data will be treated as the print data. The highlight characters remain valid until the highlight character deselection command is entered. ESC "F" [Function] [Code] [Outline] Canceling the highlight character <1B>H <46>H This command deselects the highlight characters set with ESC "E". following this command will be printed in ordinary characters. The data - 61 - ESC "-" n [Function] [Code] [Outline] Specifying/Canceling the underline <1B>H <2D>H n This command selects/deselects an underline. The underline is selected at n = 1 and deselected at n = 0. The space by the horizontal tab is not underlined. ESC "4" [Function] [Code] [Outline] Specifying the red print <1B>H <34>H This command prints its subsequent data in red. This command remains valid Red and black characters until the red print deselection command is entered. ESC "5" [Function] [Code] [Outline] Canceling the red print <1B>H <35>H This command deselects red print. - 62 - SI [Function] [Code] [Outline] Specifying the inverted character <0F>H This command selects and prints the inverted characters. Enter it at the Erect and inverted DC2 [Function] [Code] [Outline] Canceling the Inverted character <12>H This command deselects the inverted characters. Enter this command at the LF [Function] [Code] [Outline] Printing and paper feed <0A>H If the print buffer contains the data, this command will feed the line after printing. If not, the command only feeds the line. - 63 - CR [Function] [Code] [Outline] Printing and paper feed (Same as LF) <0D>H The function is the same "LF. " ON, this command is ignored. However, if the DIP switch segment 1-6 is set to ESC "z" [Function] [Code] [Outline] Setting the standard line feed width <1B>H <7A>H This command sets the line feed width as follows. For character type: For graphic type: 1/6 2/9 inch ESC "a" n [Function] [Code] [Range] [Outline] Setting the n-line paper feed <1B>H <61>H n 1 £ n £ 127 This command feeds the paper by the number of lines specified with n. [. . . ] "Power Down(Data in Buffer)" Testdruck Dumpmodus: : Um sich einen Testdruck drucken zu lassen, schalten Sie den Drucker ein, während Sie gleichzeitig den Schalter LF drücken. : Um in den Dumpmodus zu schalten, schalten Sie den Drucker ein, während Sie gleichzeitig den Schalter LF und SEL drücken. "=== Hexadecimal Dump ===" ­ 142 ­ Einschalten SEL SW ?OFF Pufferdaten NEIN ON · Das Lämpchen SEL/ERROR blinkt in Abständen von 0, 25 Sekunden. [. . . ]