User manual CITIZEN P700

[. . . ] ·Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage to the product. ·Slots and openings on the back or bottom of the case are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, do not block or cover these openings. [. . . ] subsequent data will be treated as the print data. Once the message is defined, it remains valid until it is redefined or the download deletion command (ESC DC2 n1 n2) is executed. The data If the data exceeds 50 bytes, the If the value of n is specified beyond the range, the data following n will be treated as the print 69 CITIZEN iDP-3420/3421/3423 User's Manual ESC DC3 n [Function] [Code] [Range] [Function] Printing the message <1B>H <13>H n 1 £ n £ 10 This command prints a message. If the value of n is specified beyond the range, the message will not be printed. ESC "y" n [Function] [Code] [Range] [Outline] Setting the print lines after paper near end detection <1B>H<79>H n 0 £ n1 £ 255 This command sets the number of print lines after paper near end detection. It stops printing after printing n ´ 2 lines since detection of the paper near end, resulting in the paper near end state (See 4. 12 Operation Panel and Error Indications). [Default] n=0 The PE signal (Serial/Parallel) changes when the paper near end 70 CITIZEN iDP-3420/3421/3423 User's Manual ESC DC2 n1 n2 [Function] [Code] [Range] Deleting the download character, message, bit image <1B>H <12>H n1 n2 0 £ n1 £ 3 0 £ n2 (Specify 0 at n1 = 0) (1 £ n2 £ 10 at n1 = 1) (32 £ n2 £ 255 at n1 = 2) (Specify 0 at n1 = 3) [Outline] This command deletes the downloaded characters, message, and bit image. n1 0 1 2 3 Object Deleted All(Message, characters, bit image) Download message Download characters Download bit image With n2, specify which data of the function specified with n1 should be deleted. n2 = 0 n2¹0 Deletes all the data saved with the download function specified with n1. Deletes the data downloaded at the value specified with n2 (Value specified when saving with each download command), of the download function specified with n1. Note) No meaning when n1 = 0 is set. 71 CITIZEN iDP-3420/3421/3423 User's Manual GS "*" n1 n2 [d] n1 ´ n2 ´ 8 [Function] [Code] [Range] Defining the download, bit image <1D>H <2A>H <n1> <n2> [<d>] n1 ´ n2 ´ 8 1 £ n1 £ 45 2, 048. [Outline] This command defines the download bit image having the dots specified n1 and n2. If not, the command only feeds the line. CR [Function] [Code] [Outline] Printing <0D>H This command prints the data. If the DIP switch segments 1 to 6 are set to OFF, the printer will print the data in the print buffer and feed the paper by one line. If they are set to ON, the printer will print the data in the print buffer and will not feed the paper. ESC "z" [Function] [Code] [Outline] Setting the 1/6-inch line feed width <1B>H <7A>H This command sets the line feed width to 1/6 inch (Default). 80 CITIZEN iDP-3420/3421/3423 User's Manual ESC "a" n [Function] [Code] [Range] [Outline] Setting the n-line paper feed <1B>H <61>H n 1 £ n £ 127 This command feeds the paper by the number of lines specified with n. If the print buffer contains the data, use of this command feeds the paper by n-lines after printing the data. FF [Function] [Code] [Outline] Form feed (Changing the page) <0C>H This command searches for the head of the next page after printing the data in the print buffer. ESC "C" n [Function] [Code] [Range] [Outline] [Default] Setting the n-line page length <IB>H <43>H n 1 £ n £ 255 Sets the 1-page length to n-lines. n = 42 81 CITIZEN iDP-3420/3421/3423 User's Manual ESC "C" <0> n [Function] [Code] [Range] [Outline] [Default] Setting the n-inch page length <1B>H <43>H <0> n 1 £ n £ 127 This command sets the length of one page to n-inches. n = 42 VT [Function] [Code] [Outline] Vertical tab <0B> H This command feeds the paper to the next vertical tab position. It cannot be fed unless the vertical tab position has been set. If the current position is equal to or greater than the maximum set vertical tab position, it will be fed to the head of 82 CITIZEN iDP-3420/3421/3423 User's Manual ESC "B" [n]k NUL [Function] [Code] [Range] Setting the vertical tab position <1B>H <42>H [n]k <00> 1 £ n £ 255 1 £ k £ 16 [Outline] This command cancels the already set vertical tab positions and sets new vertical tab positions. They are set in the ascending order and ends with <00>. If the tab setting position <nK> is equal or smaller than the preceding set position <nk-1>, it is assumed that setting of the vertical ESC "N" n [Function] [Code] [Range] [Outline] [Default] Setting the lower margin <1B>H <4E>H n 0 £ n £ 255 This command sets the n-line lower margin. n=0 83 CITIZEN iDP-3420/3421/3423 User's Manual ESC "O" [Function] [Code] [Outline] Canceling the lower margin <1B>H <4F>H This command deselects the set lower margin. ESC "l" n [Function] [Code] [Range] [Outline] Setting the left margin <1B>H <6C>H n 0 £ n £ (Right margin - 2) This command sets the left margin and printing starts from the column next to the set margin. ESC "Q" n [Function] [Code] [Range] [Outline] Setting the right margin <1B>H <51>Hn 2 £ n £ (Max. [. . . ] Fehlerlämpchen (ERROR) (rot) Dieses Lämpchen leuchtet oder blinkt zur Anzeige eines Fehlers. Fehleranzeige Mechanischer Fehler Papierende Papierrolle fast leer Signalgeber Etwa 1 Sekunde anhaltender Signalton Leuchtet Drei kurze Signaltöne, in Abstand von 0, 6 Sekunden wiederholt werden Blinkt (in Drei kurze Signaltöne, Sekundenabständen) in Abstand von 0, 6 Sekunden wiederholt werden Rasches Blinken Etwa 1 Sekunde langer (zweimal pro Sekunde) Signalton ERROR-Lämpchen Rasches Blinken Rückstellmethode Den Netzschalter rückstellen. Den Papierstau beseitigen. Motorsperre des Schneidemechanism us (nur iDP-3421/23) Mechanischer Fehler : Wenn der Druckmechanismus aufgrund eines Papierstaus o. dergl. höher als normal belastet wird, erklint ein Signalton, und das ERROR-Lämpchen blinkt, um den Druckmechanismus zu stoppen. Papierende : Bei aufgebrauchte-m Papiervorrat erkennt der Sensor im Papierweg in der Nähe des Druckkopfes das Ende der Papierrolle, schaltet den Signalgeber und das ERROR-Lämpchen ein, um den Druckmechanismus zu stoppen. [. . . ]