User manual CITIZEN PMU23XX BROCHURE

[. . . ] Specifications LINE THERMAL PRINTER MODEL PMU22XX / PMU23XX Rev. 1. 01 Issued on August 30, 2007 Revision Record Revised section (page) Revision 1. 00 Date 2007. 7. 26 Contents of Revision Newly issused Approved Checked Osano Compiled Watanabe / 1. 01 2007. 8. 30 P7 43 45 46 47 49 50 51 52 53 57 59 61 63 Revision / Osano / Watanabe / / / / / / -2- PMU22XX/23XX Specifications Contents 1. GENERAL OUTLINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1. 1 1. 2 1. 3 1. 4 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] However, install the resistance in accordance with the rating of the LED used. (Transistor collector-emitter saturation voltage VCE (sat) = 0. 3V (max)) · The FEED switch input terminal is as shown in the above circuit. Though a ceramic capacitor is inserted in the circuit to prevent chattering, be sure that chattering may be large depending on the switch. · Do not use this connector for other than operation external output. Wrong use may cause not only damage to the printer but also bad effect on human body, peripheral equipment, etc. - 27 - PMU22XX/23XX Specifications Control Board VCC FEED switch GND POWER LED ERROR LED Figure Example of Connection - 28 - PMU22XX/23XX Specifications 4. INTERFACES 4. 1 RS-232C Serial Interface 4. 1. 1 Connector Pin Assignment (CN101) Adaptable connector (D-Sub connector) Table No. 1 2 3 4 5 6 7 8 9 Signal NC RD TD DTR GND DSR RTS NC NC Input Output Input Output Output Connector Connection Input/Output Function Non Connect Receive data Transmit data Printer BUSY signal GND for signal Dataset Ready Printer BUSY signal Non Connect Non Connect Printer side: 17LE-23090-027 (DDK or equivalent) Cable side: 17JE-13090-02 (DDK or equivalent) * Note: Signal for RS-232C complies with EIA RS-232C. 4. 1. 2 1) 2) Specifications Synchronization system: Asynchronous Baud rate 2400, 4800, 9600, 19200, 38400, 57600, 115200bps (user selection) * For 38400 , 57600, 115200bps, only setting by customize value is available. 1 Word composition Start bit: 1 bit Data bit: 7 bits or 8 bits (user selection) Parity bit Odd, even, or no parity (user selection) Stop bit: 1 bit or more Signal polarity RS-232C Mark = Logical "1" (-3V to -12V) Space = Logical 0 (+3V to +12V) 3) 4) - 29 - PMU22XX/23XX Specifications 4. 1. 3 1) Description of Input/Output Signals Input/output signal [1] RD Receive data TD signal irregularly caused when the printer is connected to the host, when the host power is turned on or off, etc. is treated as Break signal while other data are discarded. (Turning the host off causes unstable status of TD depending on the host. Printing of unstable TD is prevented. ) [2] TD Transmit data [3] DSR When DTR/DSR control is selected, data is transmitted after confirming that this signal is Space. When XON/XOFF control is selected, data is transmitted with DSR ignored. [4] DTR, RTS Space indicates the BUSY state of the printer and Mark indicates that the printer is ready for reception. The condition for BUSY can be changed by the setting (MSW1-3). From reset (including reset by NV memory write command, I/F signal, and test print command) or just after printer power on till the printer enters the ready state 2. Input buffer full state (Refer to 2) Buffer full state. ) 4. While paper is being fed by the FEED switch 6. When waiting for pressing of the FEED switch at the execution of a macro 7. Error state Under the conditions 1 to 3 above, the printer becomes BUSY regardless of the setting of memory switch. (MSW1-3 ON: The printer does not become BUSY state regardless of the setting. ) When XON/XOFF control is selected, however, Mark state occurs under the conditions of 1 and 2. In other condition, Space state is caused. This is used for confirming the status of connection between the printer and the host. [. . . ] Specifies absolute position of character vertical direction in page mode. Specifies relative position of character vertical direction in page mode. Function MODE GS P ESC ¥ ESC GS GS GS GS a $ L W ¥ Line Feed Span Commands Control Command ESC ESC 2 3 Sets 1/6-in. Sets line feed amount in units of minimum paper feed pitch. [. . . ]