User manual CITIZEN PN60I

[. . . ] ·Follow all warnings and instructions marked on the product. ·Unplug this product from the wall outlet before cleaning. ·Do not use this product near water. ·Do not place this product on an unstable cart, stand or table. [. . . ] [Default] [See Also] n=0 ESC ! GS $ nL nH Specifying the absolute vertical position of characters in Page mode <1D>H<24>H<nL><nH> 0 £ nL £ 255 0 £ nH £ 255 This command is used in Page mode to specify the vertical position of characters at the data mapping start position as an absolute value measured from the start point. The vertical position of a character at the next data mapping start position will be at a distance of [(nL + nH ( 256) ( basic calculation pitch] inches away from the start point. ·This command is ignored when Page mode is not selected. ·Any specification of absolute vertical position out of the printable area is ignored. ·The horizontal position of a character at the data mapping start position is not moved. ·The start point used as the reference is specified by ESC T. ·Depending on the start point specified by ESC T, this command acts as follows: (1) If the start point is the top left or bottom right, the command specifies the absolute position in the paper feed direction (the character's top-bottom direction), using the vertical basic calculation pitch (y). (2) If the start point is the top right or bottom left, the command specifies the absolute position in the direction perpendicular to the paper feed (the character's top-bottom direction) using the horizontal basic calculation pitch (x). ·The basic calculation pitch is set by GS P. ·Fractions resulting from calculations are corrected with the minimum pitch of the mechanism, and the remainder is omitted. [Function] [Code] [Range] [Outline] [Caution] [See Also] ESC $, ESC T, ESC W, ESC ¥, GS P, GS ¥ GS * n1 n2 [ d ] n1 ´ n2 ´ 8 [Function] [Code] [Range] Defining the download bit image <1D>H<2A>H<n1><n2> [ < d > ] n1 ´ n2 ´ 8 1 £ n1 £ 255 1 £ n2 £ 48 n1 ´ n2 £ 1536 [Outline] Defines download bit images of the number of dots specified by n1/n2. · The numbers of dots are n1´8 in horizontal direction and n2´8 in vertical direction. · Black/white inversion specification take precedence over underline specification. Underline printing due to underline specification is, therefore, nullified if black/white inversion is specified; the underline setting, however, remains unchanged. [Default] n=0 GS H n Selecting of printing position of HRI characters <1D>H<48>H<n> 0£n£3 48 £ n £ 51 Selecting printing position of HRI characters in printing bar codes. ·"n" means the followings. n 0, 48 1, 49 2, 50 3, 51 Printing Position No printing Above the bar code Below the bar code Both above and below the bar code [Function] [Code] [Range] [Outline] [Caution] · The HRI characters refer to the bar code-turned characters so that you can read them. ·The HRI characters are printed in the font selected with GS f. ·Specify before the GS k command. [Default] [See Also] n=0 GS f, GS k [Print Results] No HRI characters Printed above LPRINT CHR$ (&H1B) + "3" + CHR$ (5) ; LPRINT CHR$ (&H1D) + "h" + CHR$ (50) ; LPRINT CHR$ (&H1D) + "H" + CHR$ (0) ; GOSUB BC LPRINT CHR$ (&H1D) + "H" + CHR$ (1) ; GOSUB BC LPRINT CHR$ (&H1D) + "H" + CHR$ (2) ; GOSUB BC LPRINT CHR$ (&H1D) + "H" + CHR$ (3) ; GOSUB BC END BC : LPRINT CHR$ (&H1D) + "k" ; LPRINT CHR$ (4) ; LPRINT "12" + CHR$ (0) ; LPRINT CHR$ (&HA) ; RETURN Printed above and below Printed below [Sample Program] GS I n Sending the printer ID <1D>H<49>H<n> 0£n£3 49 £ n £ 51 Sends the specified printer ID. n 1, 49 2, 50 3, 51 Type ID Bit 0 1 2 3 4 5 6 7 Meaning Equipped for 2-byte code support Equipped with autocutter Undefined Undefined Unused Undefined Undefined Unused Hex. 01 02 -- -- 00 -- -- 00 Decimal 1 2 -- -- 0 -- -- 0 Type of printer ID Model ID Type ID ROM version ID Specification Value (hex) iDP3221 20 See table below "Type ID" As per ROM version [Function] [Code] [Range] [Outline] [Caution] ·Under DTR/DSR control, the printer sends the printer ID after verifying that the host is ready to receive. If the host is not ready to receive, the printer waits for the host to become ready to receive. ·Under XON/OFF control, the printer sends the printer ID without checking whether the host is ready to receive or busy. ·Because this command is executed when data is mapped in the receive buffer, there may be a delay between command receiving and printer ID sending depending on the condition of the receive buffer. [. . . ] Verbleib in der Phase "Host Busy Data Not Available" 3. Setzen von HostBusy (nAutoFd) auf Low und Wechsel in die Phase "Reverse Idle" (Event 7) 10) Wenn der Drucker weitere Daten senden will, wählt der Host-Computer einen der folgenden drei Stati: 1. Setzen von HostBusy (nAutoFd) auf Low und Signalisierung, daß der Host-Computer bereit zum Empfang ist. Verbleib in der Phase "Host Busy Data Available" 3. [. . . ]