User manual CITIZEN PPU-231 BROCHURE

[. . . ] LINE THERMAL PRINTER/ PRESENTER UNIT MODEL PPU-231 User's Manual PPU-231 User's Manual Declaration of Conformity This printer conforms to the following Standards: Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/31/EEC, 93/68/EEC. LVD : EN60950 EMC : EN55022 Class A EN61000-3-2 EN61000-3-3 EN55024 This declaration is applied only for 230V model. WARNING : This is a Class A products. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. CITIZEN is a registered trade mark of CITIZEN WATCH CO. , LTD. , Japan CITIZEN es una marca registrada de CITIZEN WATCH CO. , LTD. , Japón CITIZEN PPU-231 User's Manual IMPORTANT SAFETY INSTRUCTIONS · · · · · · Read all of these instructions and save them for future reference. Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning. [. . . ] If the paper is not automatically fed, remove the paper from the paper insertion slot and try again. You can use the DIP switch to enable/disable the function. If disabled, auto-loading will not be performed. CAUTION: 1) When auto-loading is being activated, do not touch the paper roll, because it could result in a paper feed failure or cause the paper to be one-sided. 2) Be sure to set the paper until it comes into contact with the platen roller; otherwise, the paper cannot be fed and the printing head could be damaged. 4. 12 Self-Print Function This unit has a function to perform preset printing. Turn on the power with the FEED switch held down. It will print the ROM version, DIP switch state, characters used, etc. CAUTION: Do not use this function when the paper roll is running out. 4. 13 Presenter Control This unit feeds in paper while printing or transporting paper. After having operated the auto cutter, the unit delivers out the paper. The next printing operation does not start until the paper ejected is removed. (Printing is holted. ) CAUTION: Do not approach your face or hand toward the Presenter's paper output slot while the paper is being output. 23 CITIZEN PPU-231 User's Manual 5. 5. 1 DIP SWITCH SETTING Location of DIP Switch The following figure clearly shows where the DIP switches are. Any settings made while the power is turned on will not take effect. Turn the power on after you set the DIP switches. After you have made the required settings, reattach the cover and screw. Slide the cover towards you and lift it to remove (see arrows in the figure). CAUTION: 1) The DIP switch cover has sharp edges. If you do lose it, replace it with the same type. Do not use screws that are longer than 3mm. 3) Always turn off the power before setting. If you make settings while the power is on, the unit may become faulty. 4) Do not use anything sharp and pointy to set the DIP switches. 5) Always set the switches that have been specified as disabled to OFF (the setting that existed when shipped). 6) Do not use the unit while the DIP switch cover is removed. Dip Switches 24 CITIZEN PPU-231 User's Manual 5. 2 DIP Switch Function DIP switch 1 (DS1) No. DS1- 1 2 3 4 5 6 7 8 Function Auto cutter CR switching Printing density DTR-DSR/XON-XOFF Baud rate and parity setting Baud rate and parity setting Baud rate and parity setting Baud rate and parity setting See Table 1. ON Enabled LF operation OFF Disabled Ignored Upon Shipment ON OFF OFF OFF OFF OFF OFF OFF Combination with DS2-6. [. . . ] · Modes can be selected by m are shown below. Mode Name Normal mode Double wide mode Double high mode Double wide/double high mode Dot Density in Vertical Direction 203 DPI 203 DPI 101 DPI 101 DPI Dot Density in Horizontal Direction 203 DPI 101 DPI 203 DPI 101 DPI [Function] [Code] [Range] [Outline] m 0 1 2 3 [Caution] · When data exist inside the print buffer, this command is ignored. · When a download bit image has not been defined, this command is ignored. · A portion of a download bit image exceeding one line length is not printed. [. . . ]