User manual CITIZEN SDC-805BN

[. . . ] · Unplug this product from the wall outlet before cleaning. · Do not use this product near water. · Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage to the product. [. . . ] · If a new position is specified to the right of the current position in the direction of printing, it should be specified as positive (+). If it is to the left, it should be as negative(-). · A negative value is the complement of 65536. For example, to move the position by N pitches to the left, specify it as: nL + nH × 256 = 65536 - N · The basic calculation pitch is set by GS P. · Fractions resulting from calculation are corrected with the minimum pitch of the mechanism, and the remainder is omitted. · In STANDARD MODE, this command uses the horizontal basic calculation pitch (x). · In PAGE MODE, this command acts differently depending on the start point: (1) If the start point specified by ESC T is top left or bottom right, the command specifies the relative position in the direction perpendicular to the paper feed (The character's side-to-side direction), using the horizontal basic calculation pitch (x). (2) If the start point is top right or bottom left, the command specifies the relative position in the paper feed direction (The character's side-to-side direction), using the vertical basic calculation pitch (y). [Caution] [See Also] [Sample Program] ESC $, GS P Refer to Sample Program and Print Results for ESC $ on page 61. -- 86 -- ESC a n [Function] [Code] [Range] Aligning the characters <1B>H<61>H<n> 0 48 [Outline] n n 2 50 All the printed data within one line are aligned in the specified position. · Depending on the value "n", positional alignment is carried out as shown in the table below: n 0, 48 1, 49 2, 50 Position Left end alignment Centering Right end alignment [Caution] · This command is valid only when it is inputted at the beginning of a line. · The settings of this command have no effect on PAGE MODE, but items set in PAGE MODE are valid even after STANDARD MODE resumes. [Default] [Sample Program] n=0 LPRINT CHR$(&H1B) + "a" + CHR$(0); LPRINT "AAAAA" + CHR$(&HA); LPRINT CHR$(&H1B) + "a" + CHR$(1); LPRINT "AAAAA" + CHR$(&HA); LPRINT CHR$(&H1B) + "a" + CHR$(2); LPRINT "AAAAA" + CHR$(&HA); END [Print Results] AAAAA AAAAA AAAAA Left-justified Centered Right-justified Paper Feed Direction -- 87 -- ESC c 3 n [Function] [Code] [Range] [Outline] Selecting the Paper Sensor valid for a paper end signal output <1B>H<63>H<33>H<n> 0 n 255 This command selects by which Paper Sensor a paper end signal should be output. Each bit for "n" has the following meaning: Bit 0 1 2 3 4 5 6 7 Position Paper Near-end Paper Near-end Paper end Paper end Undefined Undefined Undefined Undefined Value 0 1 Disabled Enabled Disabled Enabled Disabled Enabled Disabled Enabled [Caution] This command is valid only for the parallel interface. Number Decimal Number Refer to Table 2, "Vertical Magnification". Vertical magnification specification Horizontal magnification specification Refer to Table 1, "Horizontal Magnification". Table 1 Horizontal Magnification Hex. Decimal 00 0 10 16 20 32 30 48 40 64 50 80 60 96 70 112 Magnification 1 ×(Standard) 2 ×(Double width) 3× 4× 5× 6× 7× 8× Table 2 Vertical Magnification Hex. Decimal 00 0 01 1 02 2 03 3 04 4 05 5 06 6 07 Magnification 1 ×(Standard) 2 ×(Double height) 3× 4× 5× 6× 7× 8× 7 [Caution] · This command works for all ANK characters except for HRI characters. · This command is ignored if either the vertical magnification or horizontal magnification is out of the defined range. · In STANDARD MODE, the vertical direction is defined as the paper feed direction, and the horizontal direction is defined as the direction perpendicular to the paper feed. These definitions are, therefore, interchanged when 90 -right-turned characters are specified. · In PAGE MODE, the vertical direction means the top-bottom direction of each character. The horizontal direction means the side-to-side direction of each character. -- 95 -- · If characters of different vertical magnification are contained in a line, the baseline of each character is lined up. · Horizontal and vertical magnification can also be specified/ canceled by ESC !. command, whichever is handled last, becomes effective. [Default] [See Also] n=0 ESC ! -- 96 -- GS $ nL nH [Function] [Code] [Range] Specifying the absolute vertical position of characters in PAGE MODE <1D>H<24>H<nL><nH> 0 0 [Outline] nL nH 255 255 This command is used in PAGE MODE to specify the vertical position of characters at the data mapping start position as an absolute value measured from the start point. [. . . ] Wenn die Steuerung per DTR/DSR nicht aktiviert ist, ignoriert der Computer dieses Signal und sendet Daten an den Drucker. Dieses Signal kann auch als Rücksetzungssignal nach Ändern der DIP-Schalterstellung verwendet werden (siehe 5. 2 "DIP-Schaltertabelle"). Wenn die Pulsbreite des Signals 1 ms oder länger beträgt, wird eine Rücksetzungssignal übertragen. (5) INIT Dieses Signal kann als Rücksetzungssignal verwendet werden, nachdem Sie die Stellung des entsprechenden DIP-Schalters geändert haben (siehe 5. 2 "DIPSchaltertabelle"). [. . . ]