User manual CITIZEN SLD-200III

[. . . ] Unplug this product from the wall outlet before cleaning. l Do not place this product on an unstable cart, stand of table. The product may fall, causing serious damage to the product. l Slots and openings on the cabinet and the back or bottom are provided for ventilation. [. . . ] When DTR/DSR control has not been selected, the data from the host side can be received after transmitting XON, but it cannot be received after transmitting XOFF. 7. 3. 5 Buffering There are DTR and TD signals as control signals for data transfer to the input buffer. (1) DTR signal (Refer to 7. 3 1) (2) TD signal (Refer to 7. 3 1) CITIZEN 30 CBM-230/231 User's Manual 7. 3. 6 Electrical Characteristics (1) RS-232C circuit Input (RD, DSR) Output (DTR, TD) CITIZEN 31 CBM-230/231 User's Manual 8 DRAWER KICK CONNECTOR 8. 1 Specifications (1) Drawer kick drive signal The pulses specified by ESC p are output. The state of the switch(+) can be known through the pin 34 of the interface connector when parallel interface is used, and through the ESC u command when the serial interface is used. (2) Electrical characteristics 1) Drive voltage : DC 24 V 2) Drive current : 0. 8 A at maximum(should be within 510 ms) 3) Switch signal : Signal level "L" = 0 to 0. 5 V "H" = 3 to 5 V 8. 2 Connector's Pin Configuration No. 1 2 3 4 5 6 SIGNAL NAME FG DRAWER 1 DRSW VDR DRAWER 2 GND FUNCTION Frame ground Drawer 1 driving signal Drawer SW input Drawer driving power supply Drawer 2 driving signal Common ground on the circuits Connector used Applicable connector : TM5RJ3-66(HIROSE) :Equivalent to TM3P-66P(HIROSE) [Cautions] 1) No output is allowed during printing. 2) The drawers 1 and 2 cannot be driven at the same time. 3) A solenoid for the drawer should be of 36 Ohm or more. (See to it that an output current will not exceed 0. 8 A. Be careful not to use a drawer with a current over 0. 8A to avoid damage to the printer. ) 8. 3 Drive Circuit CITIZEN 32 CBM-230/231 User's Manual 9 PRINT CONTROL FUNCTION 9. 1Control Codes List 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 CONTROL CODE HT CR LF ESC SP !% & * 2 3 @ D E G J R c3 c4 c5 d p t v u { V $ ¥ GS k w h H f * / : ^ ESC = a i m FUNCTION Horizontal tab command Print command Printing and paper feed Setting the right space amount of the character Collective specifying printing mode Specifying/canceling download character set Defining download characters Specifying the bit image mode Specifying/canceling underline Specifying 1/6-inch line feed rate Setting line feed rate n/203 inch Initializing the Printer Setting horizontal tab position Specifying/canceling highlighting Specifying/canceling double printing Printing and feeds paper n/203 inch Selecting the international characters Setting of paper end sensor effective for outputting a signal for no paper(Parallel Mode Only) Setting of paper end sensor effective for print stop Enabling/disabling the panel switches Printing and feeding the paper by n lines Generating the specified pulse(Drawer Kickout) Selecting the character code table Transmitting the printer status(Serial Mode Only) Transmitting the status of peripheral equipment(Serial Mode Only) Specifying/canceling the inverted characters Specifying/canceling the 90°- right-turned characters Specifying the absolute positions Specifying the relative positions Printing the bar code Selecting the horizontal size (scale factor) of bar code Selecting the height of the bar code Selecting the printing position of HRI character Selecting the font of HRI character Defining the download bit image Printing the download bit image Starting/ending macro definition Executing the macro Data input control Aligning the characters Full cut Partial cut CITIZEN 33 CBM-230/231 User's Manual 9. 2Input Data Format (1) Horizontal Tab Command (HT) Code : (09)h Shifts the printing position to the next horizontal tab position. The horizontal tab position is set by ESC D. l "a" indicates the number of dots in horizontal direction for definition. l Dn is the data to be defined, which indicate a pattern equal to "a" dot in horizontal direction from the left end. The rest of the pattern on the right side is filled with space. l Download characters thus defined remain valid until redefinition, ESC @ execution, GS * execution, or power OFF is practiced. CITIZEN 36 CBM-230/231 User's Manual Example For Font A CITIZEN 37 CBM-230/231 User's Manual For Font B CITIZEN 38 CBM-230/231 User's Manual (8) Specifying the Bit Image Mode (ESC * m n1 n2 D1 -Dn) Code : [1B]h + [2A]h + m + n1 + n2 + Dn * {m= bit image mode (See the table below. )} {0 n1 FF} {0 n2 02} Data is described in Hex code. According to the bit image mode assigned in m, prints data in the bit image. of dots printed is divided by 256, whose quotient is taken as n2 and residualas n1. of dots printed in the bit image is equal to n1 + (256 x n2). l When bit image data have been input in excess of 1 dot/line (448 dots) position, the excess data are discarded. l In the bit image data (Dn), the bits subject to printing are taken as "1" and those not as "0". l The bit image modes are shown as follows: VERTICAL DIRECTION HORIZONTAL DIRECTION m(Hex) MODE NO. NO OF DOTS 0 8-dot single density 8 67 DPI 101 DPI 288 1 8-dot double density 8 67 DPI 203 DPI 576 20 24-dot single density 24 203 DPI 101 DPI 288 21 24-dot double density 24 203 DPI 203 DPI 576 l When the value set in m (bit image mode) are out of conditions, the data following after n1 is processed as printing data. CITIZEN 39 CBM-230/231 User's Manual The relation between bit image data and printing dots are shown below. [. . . ] l Depending on n value, positional alignment is carried out as in the table below: n (Hex) POSITION 0 Left end alignment 1 Centering 2 Right end alignment l This is valid only when n is inputted at the beginning of line. l The initial value of n is "0". (40) Full Cut (ESC i) Code : [1B]h + [69]h Full cutting of paper is performed. l This is valid only when n is inputted at the beginning of line. [. . . ]