User manual CITIZEN SLD-366

[. . . ] The product may fall, causing serious damage to the product. l Slots and openings on the cabinet and the back or bottom are provided for ventilation. To ensure reliable operation of the product and to protect it form overheating, do not block or cover these openings. The openings should never be blocked by placing the product on a bed, sofa, rug of other similar surface. [. . . ] Absolutely, do not carry out clearing problem supplying power. l Head-up condition Pull down had up lever forward. Print head is pulled down and error signal is cleared, then printer becomes ready for print. l Heating up of print head temperature When temperature of print head is getting high due to continuous printing etc. , printer stops printing. During temperature of print head is high, any operation is not available, keep printer without printing. As soon as temperature of print head goes low, error signal is canceled automatically and printer becomes ready for print. CITIZEN 22 4. Dip switch setting Dip switch locates on the rear side of main body. Make sure that power is turned OFF before changing Dip switch settings. Change during power is ON can not be effective. DIP SWITCH DS1-1 AUTO CUTTER 2 CR SELECTION 3 PRINT DENSITY 4 DTR-DSR/XON-XOFF 5 INTERFACE 6 " 7 " 8 " ON EQUIPPED LF ENABLE STANDARD XON-XOFF OFF NONE LF DISABLE DARKER DTR/DSR FACTORY SETTING OFF = SLD-366 ON = CBM-291 OFF OFF OFF OFF OFF OFF OFF SEE BELOW DS18 OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON 7 OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON 6 OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON 5 OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON INPUT METHOD PARALLEL INPUT SERIAL INPUT " " " " " " " " " " " " " " PARITY -NONE " " " " ODD " " " " EVEN " " " " BAUD RATE -1200 bps 2400 bps 4800 bps 9600 bps 19200 bps 1200 bps 2400 bps 4800 bps 9600 bps 19200 bps 1200 bps 2400 bps 4800 bps 9600 bps 19200 bps Remarks : For SLD-366, It make Error when ON is selected for DS1-1. DS1-4 is ignored when parallel input is specified. 6. 6 Buffering 4 K bytes input buffer is incorporated. Due to this large buffer, host side is released immediately. CITIZEN 27 7 Serial Interface 7. 1 Specifications (1) Data transfer system: Asynchronous (2) Baud rates 1200, 2400, 4800, 9600, 19200 bps (Selectable by user) (3) Configuration of one word Start bit : 1 bit Data bit : 8 bits Parity bit : Add/even or no parity (Selectable by user) Stop bit : 1 bit or more (4) Signal polarity RS-232C l Mark = logic " 1" (-3V - -12V) l Space = logic " 0" (+3V - +12V) (5) Receiving data (RD signal) RS-232C l Mark = 1 l Space = 0 (5) Receiving control (DTR signal) RS-232C l Mark : Data transfer not available l Space : Data transfer available (6) Transmission control (TD signal) DC1 code (11H) X-ON : Data reception available DC3 code (13H) X-OFF : Data reception not available CITIZEN 28 7. 2 Explanation of Input / Output signals 7. 2. 1 Input / Output signals (1) RD Serial receiving data signal. On occurrence of framing error, overrun error, or parity error, the data is printed as "?". (2) DTR When this signal is READY, write data or a command. When they are written in BUSY, overrun error is occurred and data is ignored. Even during printing, data can be loaded in the input buffer. Further, BUSY can take place on supply of power, during test printing, during on-line, or on resetting. (3) TD When, while in data reception, the rest of input buffer on the printer side goes less than 128 bytes , DC3 (13H) data reception impossible signals are output. When the rest of input buffer goes more than 256 bytes, DC1 (11H) data reception possible signals are output to the host. When DTR/DSR control having been selected in status information transmission, it is first confirmed that DSR is "space" and data is sent. When DTR/DSR control has not been selected, DSR is ignored and data is transmitted. [. . . ] A download character and a download bit image cannot be defined simultaneously. (37) Starting / Ending Macro Definition (GS :) Code : [1D]h + [3A]h Specifying starting / ending macro definition. Maximum content available for macro definition is 2048 bytes. A portion exceeding 2048 bytes is not defined. l Even with ESC @ (initialization of the printer) having been executed, defined content is not cleared. [. . . ]