User manual CITIZEN SLD-377

[. . . ] ·Unplug this product from the wall outlet before cleaning. ·Do not use this product near water. ·Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage to the product. [. . . ] ) · Specification with this command is invalid to Kanji, except specification and cancellation of highlighting · In case that double wide character and normal character exist in same one line, the layout of underline is consistent one. n=0 ESC E, ESC LPRINT CHR$ (&H1B) ; " !" ; CHR$ (&H00) ; "H" ; LPRINT CHR$ (&H1B) ; " !" ; CHR$ (&H01) ; "H"; LPRINT CHR$ (&H1B) ; " !" ; CHR$ (&H08) ; "H"; LPRINT CHR$ (&H1B) ; " !" ; CHR$ (&H10) ; "H"; LPRINT CHR$ (&H1B) ; " !" ; CHR$ (&H20) ; "H"; LPRINT CHR$ (&H1B) ; " !" ; CHR$ (&H80) ; "H"; LPRINT CHR$ (&H1B) ; " !" ; CHR$ (&HB9) ; "H"; LPRINT CHR$ (&HA) ; END [Default] [See Also] [Sample Program] [Print Results] 51 CITIZEN SLD-377 User's Manual ESC % n Specifying/Canceling download character set <1B> H <25> H <n> 0 £ n £ 255 Specifying/canceling download characters. Further, only the lowest bit (n0) is valid for n. The lowest bit (n0) indicates the following. 1 Specifying an underline for 1-dot width 2 Specifying an underline for 2-dots width · An underline is attached to the full character width. It is, however, not attached to the part having been skipped by horizontal tab command. · An underline is not attached to a 90 °- right-turned characters. · Specification/cancellation with this command is invalid to Kanji. ESC !, FS LPRINT CHR$ (&H1B) ; "-" ; CHR$ (0) ; LPRINT "AAAAA" ; LPRINT CHR$ (&H1B) ; "-" ; CHR$ (1) ; LPRINT "AAAAA" ; CHR$ (&HA) ; END [Caution] [See Also] [Sample Program] [Print Results] ESC [Code] 2 Specifying 1/6-inch line feed rate <1B> H <32> H The line feed rate per line is specified by 1/6 inch. [Print Results] LPRINT "AAAAA" ; CHR$ (&HA) ; LPRINT CHR$ (&H1B) ; "3" ; CHR$ (0) ; LPRINT "AAAAA" ; CHR$ (&HA) ; LPRINT CHR$ (&H1B) ; "3" ; CHR$ (50) ; LPRINT "AAAAA" ; CHR$ (&HA) ; LPRINT CHR$ (&H1B) ; "2" ; LPRINT "AAAAA" ; CHR$ (&HA) ; LPRINT "AAAAA" ; LPRINT CHR$ (&H1B) ; "J" ; CHR$ (100) ; LPRINT "AAAAA" ; CHR$ (&HA) ; LPRINT "AAAAA" ; CHR$ (&HA) ; [Function] [Outline] [Sample Program] 56 CITIZEN SLD-377 User's Manual ESC [Code] 3 n Setting line feed rate of minimum pitch <1B> H <33> H <n> 0 £ n £ 255 The line feed rate per line is specified by n/360 inch. Since an actual mechanical pitch is 1/203 inch, it is internally converted approximate to the value specified with this command. [Function] [Range] [Outline] [Default] ·The initial value is n = 60 (1/6 inch) (18H), being 4. 23 mm line feed rate. [Print Results] See Sample Program and Print Results for ESC 2 on Page 54. [Sample Program] ESC [Code] = n Data input control <1B> H <3D> H <n> 0 £ n £ 255 Selecting equipment in which data input from the host is effective. · Each bit of n indicates as follows: Bit 0 1 2 3 4 5 6 7 Equipment Printer Not defined Not defined Not defined Not defined Not defined Not defined Not defined 0 Invalid Value 1 Valid [Function] [Range] [Outline] · When the printer has not been selected, this printer abandons all the received data until it is selected by this command. [Caution] · Even when the printer has not been selected, it can become BUSY state through printer operation. · When the printer is deselected, this printer discards all the data until it is selected with this command. [. . . ] Zum Schutz der Lebensdauer des Thermalkopfes verwenden Sie die folgende Druckrate als Richtlinie; verwenden Sie die Festteilungs (6-Teilung) Methode. Kontinuierlicher Druck mit nur hoher Energie : 6% oder weniger 2. Gemischter kontinuierlicher Druck mit niedriger und hoher Energie : 30% oder weniger der Standarddruckrate von 12. 5% 3. Druckrate pro Punktzeile (3) Minimale Punkte für Hochenergiedruck Wenn Hochenergiedruck verwendet wird, ist der empfohlene minimale Bereich 3 Punkte (Länge) ´ 3 Punkte (Breite) oder mehr. [. . . ]