User manual CLARION MS8200

[. . . ] . Page 8 Jumper and Switch Settings Jumper Selections . . Page 12 Accessing the Jumpers and Switches . . Page 13 Setting the Jumpers and Switches . . Page 13 Remote Transmitters Using the Remote Transmitters . [. . . ] The LED will stay on for 5 seconds, then turn off, returning Buttons 1 and 2 to their off settings. The default setting of the Remote Transmitter is as pictured, where Button 1 is used to arm and disarm the system , Button 2 operates Auxiliary Function 1, Mode + 1 operates Auxiliary Function 2, etc. LED color none BUTTON 1 BUTTON 2 MODE BUTTON green orange red ARM Aux 1 Aux 2 Aux 3 Aux 4 not used Mode Button Sequence not used not used None:Green:Orange:Red:Green:. . . However, it is possible to set individual Remote Transmitters to arm and disarm the system using any of the Transmitters function Buttons, which is extremely useful when a Transmitter is used to control multiple system. See Adding a Remote Transmitter into the System. The Button Assignment of Arming and Disarming will not affect the operation of the Remote Page 14 - MS8200 / MS8300 Installation Manual during Programming, Logic Sensor II Adjustment, Space Shield III Adjustment, Real Time System Verification or any other system set-up function. The Buttons used to control those features will remain as they are described in this manual, regardless of how the Transmitter is set up to arm and disarm the system. Two Car Operation To use a single transmitter to operate multiple vehicles, the Transmitter can be set to arm Car #1 with Button 1 and arm Car #2 with the first available Button not being used by Car #1, which will be Mode, Mode, 1 if Car #1 is using Auxiliary functions 1 through 3. The Auxiliary functions for Car #2 will follow the arm/disarm button in sequential order. LED color none BUTTON 1 BUTTON 2 MODE BUTTON green orange red ARM (A) Aux 2 (A) Aux 1 (A) Aux 3 (A) ARM (B) Aux 1 (B) Mode Button Sequence Aux 2 (B) Aux 3 (B) None:Green:Orange:Red:Green:. . . A = Car 1 B = Car 2 As stated, the Programming and set-up functions of Car #2's system will not be affected by this Transmitter configuration and will operate exactly as described described in this manual. MS8200 / MS8300 Installation Manual - Page 15 Adding a New Transmitter into the System 1. · The status LED will turn on red. Within 5 seconds: Continue holding the Override switch and Press Transmitter Button 1* For remote arming with chirp confirmation. --- or --Release the Override switch and Press Transmitter Button 1* For remote arming without chirp confirmation. · The status LED will flash once quickly to confirm that the new Remote Transmitter has been added. Turn off the ignition. Deleting Transmitters (Adding a Remote Transmitter and Erasing All Other Remote Transmitters From the System) 1. · The status LED will turn on red. · After 5 seconds, the status LED will flash 4 times, then turn on red again. Within 5 seconds: Continue holding the Override switch and Press Transmitter Button 1* For remote arming with chirp confirmation. --- or --Release the Override switch and Press Transmitter Button 1* For remote arming without chirp confirmation. · The status LED will flash once quickly to confirm that the new Remote Transmitter has been added. Turn off the ignition. * The Button that is pressed will be the Arm/Disarm Button on that Remote Transmitter. You may program any of the Transmitter's buttons to arm and disarm the system at this point. Page 16 - MS8200 / MS8300 Installation Manual Programming System Initialization and Default Reset Following this procedure will set all System Programming Parameters to factory default settings. After 4 seconds, press and hold Buttons 1 and 2 together for 5 seconds. The siren will emit one long chirp, indicating that the reset signal was received. · · · · · All System Programming parameters are now set to factory default settings. The Arming Mode is set to Remote Arming only. The Logic Sensor II shock sensitivity is set to Level 6. The Logic Sensor II motion sensitivity is set to Level 4. Arming Mode Selection (Passive or Active Arming) Using the Remote Transmitter, you may select Passive Arming with chirp confirmation, Passive Arming without chirp confirmation, or Active Arming (Remote only). [. . . ] · The siren will emit one long chirp. · The Starter Kill and the Armed outputs will activate. Input Test Test the starter kill by turning the ignition key to the start position. (Open the door) · The siren will chirp once. With the door open: Test the override switch. [. . . ]